Southbend SB1017 owner manual Machine Labels, PSBLABEL15S Electricity Label

Page 53

For Machines Mfg. Since 8/09

P A R T S

Model SB1017

Machine Labels

308

307

306

305

304

309	310	303
		303

313

312

301

REF	PART #	DESCRIPTION
301	PSB1017301	MACHINE ID LABEL
302	PSB1017302	MODEL NUMBER LABEL
303	PSBLABEL15S	ELECTRICITY LABEL
304	PSB1017304	BELT COVER WARNING LABEL
305	PSBLABEL02HS	DISCONNECT WARNING LABEL
306	PSB1017306	CUTTING HAZARD WARNING LABEL
307	PSBLABEL04HS	EYE INJURY WARNING LABEL

311

302

REF	PART #	DESCRIPTION
308	PSBLABEL01HS	READ MANUAL LABEL
309	PSBLABEL13VS	DOOR CLOSED WARNING LABEL
310	PSBPAINT01	SB LT GRAY TOUCH-UP PAINT
311	PSBPAINT03	SB DK BLUE TOUCH-UP PAINT
312	SB1320	SOUTH BEND NAMEPLATE 125MM
313	PSBPAINT02	SB LT BLUE TOUCH-UP PAINT

The safety labels provided with your machine are used to make the operator aware of the machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of these safety labels. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact South Bend Lathe Co. at

(360)734-1540 or www.southbendlathe.com to order new labels.

-51-

Image 53

Contents Bandsaw Customer Service UpdatesScope of Manual Manual FeedbackTable of Contents Capabilities FeaturesAbout This Machine ON/OFF IdentificationMachine Specifications Machine SpecificationsMain Specifications Operation Information Understanding Risks of Machinery Basic Machine SafetyF E T Y Additional Metal Bandsaw Safety Power Supply Requirements Required for SetupAvailability Full-Load Current RatingCircuit Information For 110V Connection PrewiredCircuit Requirements for Grounding RequirementsExtension Cords Inventory UnpackingTo assemble the bandsaw AssemblyLoosen the belt tension bolt shown in Figure Installing belt Basic steps for removing rust preventative Cleaning & ProtectingBefore cleaning, gather the following Location Inspections Adjustments Power ConnectionTest Run To test run your machineOperationPERATIONOverview Downfeed Rate Adjust Knob Controls Blade Tension Knob Adjusts the positionON/OFF Toggle Switch Turns the saw ControlsBlade Terminology Blade SelectionBlade Length Blade WidthTooth Type Tooth SetTo select the correct blade pitch Blade Pitch TPITo change the blade on the bandsaw Blade ChangesBlade Breakage Blade TensionTo tension the blade on the bandsaw Most common causes of avoidable blade breakage areBlade Speed Blade Care & Break-InBlade Care Blade Break-InChip Inspection Chart Blade Speed ChartDownfeed Pressure To install and use the work stopDownfeed Rate Work StopTo use the vise ViseBlade Guide To adjust the blade guideVertical Cutting To convert the saw for vertical cuttingVertical Cutting Operation TipsHorizontal Cutting SBL Gearhead T-Shirt SBL One Good Turn T-Shirt AccessoriesGearbox CleaningLubrication To replace the V-belt Belt ReplacementMachine Storage Blade Tracking To adjust the blade tracking on the bandsawDownfeed Stop Bolt Blade Guide Bearings To adjust the blade guide bearingsSquaring Blade To adjust the auto-OFF tabAuto-OFF Tab To square the blade to the tableModel SB1017TROUBLESHOOTING For Machines Mfg. Since 8/09 Troubleshooting Dull blade missing teeth Replace blade Wiring Diagram Color KEY ElectricalL CTRICALSafety InstructionsTo convert the Model SB1017 to 220V Conversion110V Wiring DiagramR T S Cabinet Stand Head PK23M Head Parts ListMotor & Blade Guides Plastic Washer Motor & Blade Guides Parts ListSwitch PSBLABEL15S Electricity Label Machine LabelsT E S R R a N T Y Southbendlathe.com