![](/images/new-backgrounds/1314450/31445081x1.webp)
For Machines Mfg. Since 8/09 | TROUBLESHOOTING | Model SB1017 |
Symptom
Possible Cause
Possible Solution | ! |
Machine stalls | 1. | Too much pressure when feeding | 1. | Reduce pressure when feeding workpiece. |
or slows when |
| workpiece. |
|
|
operating. | 2. | Workpiece is warped and binding | 2. | Fabricate a jig for better workpiece control. |
| ||||
|
| blade. |
|
|
3.Blade is not correct for material 3. Use the correct blade for the operation. Refer to
|
| being cut. |
| Blade Selection section beginning on Page 25. | |
| 4. | Belt slipping. | 4. | Tension/replace belt; ensure pulleys are aligned. | |
| 5. | Motor overheated. | 5. | Let cool, clean motor, and reduce workload. | |
| 6. | Motor connection wired incorrectly. | 6. | Review wiring diagram on motor cover; correct wire | |
|
|
|
| connections. | |
| 7. | Motor at fault. | 7. | Test for shorted windings, bad bearings and repair | |
|
|
|
| or replace. | |
|
|
|
|
| |
|
|
|
|
| |
Workpiece angle | 1. | Scale not calibrated or loose vise. | 1. | Zero fence to blade and realign scale. Tighten any | |
incorrect or out of |
|
|
| loose fasteners. | |
square. | 2. | Table guide post is loose or out of | 2. | Tighten any loose hardware or lock levers. Align the | |
| |||||
|
| alignment. |
| guide post (see Page 37). | |
|
|
|
|
| |
|
|
|
|
| |
Machine or blade | 1. | Excessive load on the blade. | 1. | Reduce feed rate or increase blade speed | |
bogs down in the | 2. | Blade is dull, wanders, and gets | 2. | Replace blade, adjust guides and tracking. | |
cut. | |||||
| pinched in the cut. |
|
| ||
|
|
|
| ||
| 3. | Blade is dull. | 3. | Replace blade. | |
| 4. | The blade TPI is too coarse for the | 4. | Use a blade with at least 3 teeth contacting the | |
|
| thin workpiece. |
| material at all times. | |
| 5. | Blade is loose. | 5. | Clean wheels and increase blade tension. | |
| 6. | 6. | Tighten | ||
| 7. | Blade is loading up. | 7. | Install a blade with more suitable TPI or different | |
|
|
|
| style of teeth. | |
| 8. | 8. | Replace | ||
|
|
|
|
| |
|
|
|
|
| |
Blade tracks | 1. | Feed rate is too fast. | 1. | Reduce feed rate, or decrease blade TPI. | |
incorrectly, or | 2. | Blade guides need adjustment. | 2. | Adjust blade guides. | |
comes off wheels. | |||||
3. | Blade is not tracking correctly. | 3. | Adjust blade tracking. | ||
| |||||
| 4. | Blade is | 4. | Install new blade, and regularly remove tension | |
|
|
|
| from blade when not in use. |
5.Blade is dull, wanders, and gets 5. Replace blade,
| pinched in the cut. |
| shifting. |
6. | Rubber tire on wheel is damaged, | 6. | Replace rubber tires. |
| glazed, or worn. |
|
|
7. | Blade tension is too loose. | 7. | Increase blade tension. |
8. | Incorrect blade for bandsaw. | 8. | Install correct blade for machine. |
9. | The blade has insufficient support. | 9. | Tighten the blade guide as close to the workpiece as |
|
|
| possible without touching it. |
10. | Wheel tires are loaded with metal | 10. | Clean wheel tires. |
| shavings. |
|
|