Woodstock W1752 owner manual Always Lock Mobile Bases if Used Before Operating Machinery

Page 9

W1752 Owner's Manual (Mfg. 1/07+)

10.NEVER LEAVE WHEN MACHINE IS RUNNING. Turn power off and allow all moving parts to come to a complete stop before leaving machine unattended.

11.DO NOT USE IN DANGEROUS ENVIRONMENTS. DO NOT use machinery in damp, wet locations, or where any flammable or noxious fumes may exist.

12.KEEP WORK AREA CLEAN AND WELL LIT. Clutter and dark shadows may cause accidents.

13.USE A GROUNDED EXTENSION CORD RATED FOR THE MACHINE AMPERAGE. Undersized cords over- heat and lose power. Replace extension cords if they become damaged. DO NOT use extension cords for 220V machinery.

14. ALWAYS DISCONNECT FROM POWER SOURCE BEFORE SERVICING MACHINERY. Make sure switch is in OFF position before reconnecting.

15.MAINTAIN MACHINERY WITH CARE. Keep blades sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories.

16.MAKE SURE GUARDS ARE IN PLACE AND WORK CORRECTLY BEFORE USING MACHINERY.

17.REMOVE ADJUSTING KEYS AND WRENCHES. Make a habit of checking for keys and adjusting wrenches before turning machinery ON.

18.CHECK FOR DAMAGED PARTS BEFORE USING MACHINERY. Check for binding and alignment of parts, broken parts, part mounting, loose bolts, and any other conditions that may affect machine operation. Repair or replace damaged parts.

19.USE RECOMMENDED ACCESSORIES. Refer to the instruction manual for recommended accessories. The use of improper accessories may cause risk of injury.

20.DO NOT FORCE MACHINERY. Work at the speed for which the machine or accessory was designed.

21.SECURE WORKPIECE. Use clamps or a vise to hold the workpiece when practical. A secured workpiece protects your hands and frees both hands to operate the machine.

22.DO NOT OVERREACH. Keep proper footing and balance at all times.

23.MANY MACHINES WILL EJECT THE WORKPIECE TOWARD THE OPERATOR. Know and avoid condi- tions that cause the workpiece to "kickback."

24.ALWAYS LOCK MOBILE BASES (IF USED) BEFORE OPERATING MACHINERY.

25.Be aware that certain dust may be hazardous to the respiratory systems of people and animals, especially fine dust. Make sure you know the hazards associated with the type of dust you will be exposed to and always wear a respirator approved for that type of dust.

-7-

SAFETY

Image 9
Contents OWNERS MANUAL Page Contents Woodstock Technical Support IntroductionOverall Dimensions MotorElectrical Other Specifications Main SpecificationsControls and Features Standard Safety Instructions SafetyAlways Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Wood Lathes Safety Electrical Electrical Specifications110V Operation Extension CordsUnpacking SET UPInventory Box Inventory FigureMachine Placement Cleaning Machine To install the tool rest, do these steps AssemblyTo test run the mini wood lathe, do these steps Test RunGeneral OperationsChanging Speeds Adjusting TailstockTo change speeds, do these steps To position the tailstock along the bed, do these stepsInstalling/Removing Spur Center Adjusting Tool RestTo adjust the tool rest vertically, do these steps To install the spur center, do these stepsInstalling/Removing Live Center To install the live center, do these stepsTo remove the live center, do these steps Installing/Removing Faceplate To install the faceplate, do these stepsTo mount a workpiece to your faceplate, refer to Gouge Selecting Turning ToolsSpindle Turning To set up a spindle turning operation, do these stepsSpindle Turning Tips Faceplate Turning To mount your workpiece to the faceplate, do these stepsTo mount your workpiece to a backing block, do these steps Entanglement Hazard Sanding/FinishingLathe Accessories AccessoriesCleaning MaintenanceLubrication Unpainted Cast IronTroubleshooting ServiceConstant Paddle Switch Wiring Diagram W1752Parts REF PART
# Description Parts ListPART
# Description Label PlacementPage Page Page Woodstock international inc. p.o. box Bellingham, Wa Warranty High Quality Machines and Tools