Jet Tools 708315BTA operating instructions Safety Devices, Maintenance, Feather Board, Cleaning

Page 26

Figure 39

Safety Devices

Feather Board

The feather board (Figure 40) should be made of straight grain hardwood approximately 1" thick and 4" to 8" wide depending on the size of the machine. The length is developed in accordance with intended use. Feather boards can be fastened to the table or rip fence by use of C-clamps. If this method of fastening is used, provide slots in the feather board for adjustment. (The illustration shows a method of attaching and use of the feather board as a vertical comb. The horizontal application is essentially the same except that the attachment is to the table top.)

Figure 40

Push Stick

A push stick is provided with this saw and should be used as an added level of safety for the operator.

Filler Piece

A filler piece (Figure 41) is necessary for narrow ripping and permits the blade guard to remain on the machine. It also provides space for the safe use of a push stick.

Figure 41 – Filler Piece

Maintenance

Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious personal injury.

Cleaning

Clean the 708315 Table Saw according to the schedule below to ensure maximum performance.

Note: The following maintenance schedule assumes the saw is being used every day.

Daily:

Clean pitch and resin from the saw blade.

Weekly:

Clean motor housing with compressed air.

Wipe down the table surface, grooves and fence rails with a dry silicon lubricant.

26

Image 26

Contents Table Saw Part No. M-708315Warranty More Information WMH Tool Group WarrantyTable of Contents Page Page Kickback Prevention Protection Tips from KickbackSpecifications Definitions and TerminologyShipping Contents Contents Table Index Description QuantityLeg Assembly AssemblyWhere to Begin Models LSA, LSBRubber Feet Mounting the ShelfDust Shroud Model LSB onlyAll models Installing the Blade Guard and SplitterAligning the Blade Guard and Splitter Calibrating the Rip Fence Scale Saw BladeAttaching the Rip Fence Stamped Steel Extension Wing InstallationAdjustment Model BTB the extension wing should look likeSliding Extension Wing Assembly if requiredMounting the Right Extension Wing Assembly Right Scale Extension Mounting the Left Extension Wing AssemblyLeft Scale Extension Left rail extension is now properlyModels BTB, BTC and LSA Optional Left Table SupportHandwheel Handle Scale Calibration AdjustmentsDegree Positive Stop Tighten the blade tilt lock knob BAdjusting Blade Parallel to Miter Gauge Slots Replacing the BladeReplacing/Adjusting the Drive Belt For Replacement and AdjustmentOperating Controls Extension Cord ChartElectrical Connections Miter Gauge OperationKickbacks OperationsTable Saws Rip Sawing Crosscutting Do not use the standard table insert for dadoing operations Bevel and Miter OperationsDust Collection Cleaning Safety DevicesMaintenance Feather BoardParts TroubleshootingOrdering Replacement Parts LubricationMotor/Trunnion Parts List Index No. Part No Description Size Qty708315-53 Motor/Trunnion -- Assembly Blade Guard Assembly Miter Gauge Assembly Rear Support Assembly Rip Fence Assembly Right Extension Assembly Left Extension Assembly Main Saw Parts Main Saw Assembly Accessories Stand AssemblySteel Wing Assembly 708315-159 Dust ShroudWMH Tool Group Sierra de mesa de 10 pulgadas Garantía Más información Garantía de WMH Tool GroupÍndice Advertencia Advertencia Prevención de contragolpes Consejos prácticos para protegerse contra los contragolpesEspecificaciones Definiciones y terminologíaHerramientas necesarias no incluidas ContenidoContenido de las cajas Contenido de las cajasNúm. de Índice Parte Descripción Cantidad Tabla de contenidoModelos LSA, LSB ArmadoPara empezar Montaje del estante Pies de cauchoCubierta contra el polvo Modelo LSB únicamenteTodos modelos Instalación del resguardo de la hoja y placa abridoraAlineación del resguardo de la hoja y placa abridora Apriete los tornillos de cabeza hexagonal HCalibrado de la escala de la guía para cortar al hilo Hoja de la sierraAjuste de la guía para cortar al hilo Ajustes Prolongación de la mesa en acero estampadoInstalación Reposicionamiento del riel delanteroProlongación deslizable de la mesa ArmadoLa prolongación izquierda del riel está ahora Prolongación de la escala izquierdaProlongación de la escala derecha Modelos BTC, LSA y LSBModelos BTB, BTC y LSA Soporte izquierdo para la mesa, opcionalRueda de mano Calibrado de la escala AjustesParada positiva de 90 grados Parada positiva de 45 gradosFigura Reemplazo y ajuste Cambio de la HojaReemplazo/Ajuste de la Correa de Accionamiento Ajustes Operación del calibre de ingletesRetire la correa E de las poleas del motor y mandril F, G Tabla de cordones de prolongación Conexiones EléctricasControles de Operación Contragolpes OperacionesSierras de mesa Cortes al hilo Cortes transversales Operaciones de bisel e inglete Pieza de madera de empuje Dispositivos de seguridadTabla escalonada Recolección del polvoLimpieza MantenimientoPieza de relleno LubricaciónIdentificación y solución de problemas Síntoma Causa posible SoluciónMotor/Muñón Lista de partes PartesPedido de repuestos Núm. de Índice Parte Descripción Tamaño CantTS-1541021 Tuerca de bloqueo del accesorio Motor/Muñón Ensamble Ensamble del resguardo de la hoja Ensamble del calibre de ingletes Ensamble del soporte trasero Ensamble de la guía para cortar al hilo Ensamble de la prolongación derecha de la mesa Ensamble de la prolongación izquierda de la mesa Sierra principal Partes Sierra principal -- Ensemble Accesorios Ensamble del soporteEnsamble de la prolongación de la mesa en acero Descripción Tamaño CantPage WMH Tool Group