Delta 33-830 instruction manual Functional Description, Unpacking and Cleaning

Page 6

FUNCTIONAL DESCRIPTION

FOREWORD

Delta Model 33-830 is a 10" (254mm) Professional Radial Arm Saw with maximum cutting capacity of 16" (406mm) crosscut, 2-3/4" (70mm) depth at 90° and 2-1/2" (64mm) depth at 45° bevel. It is designed with positive bevel stops at 0°, 45° and 90° and positive miter stops at 0° and 45° both right and left. Unit includes; 1-1/2 hp 120/240V motor, automatic blade brake, saw blade, wrenches, steel stand, cast-iron track and extra-large table.

UNPACKING AND CLEANING

Carefully unpack the tool and all loose items from the shipping container(s). Remove the protective coating from all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces with a good quality household floor paste wax.

NOTICE: THE MANUAL COVER PHOTO ILLUSTRATES THE CURRENT

PRODUCTION MODEL. ALL OTHER ILLUSTRATIONS ARE REPRESENTATIVE

ONLY AND MAY NOT DEPICT THE ACTUAL COLOR, LABELING OR

ACCESSORIES.

1.The saw is packed at the factory with support blocks (A) Fig. 1, under the cutter-head (B), and track arm (C). Shipping boards (D) Fig. 1 are fastened to saw base (G). To prevent damage during shipment, the track arm elevating knob (H) is disassembled from lever (E). Before proceeding, insert post of knob (H) Fig. 2, through hole in lever (E) and assemble E-ring (K), to slot in post.

2.The support blocks (A) Fig. 1, can be removed by rotating track arm elevating knob (H) clockwise and the shipping boards (D) can be removed by removing hold- down screws (not shown), which are located inside saw base. Discard the support blocks (A) and shipping boards

(D).

3Fig. 3, illustrates the saw with support blocks and shipping boards removed.

C H E

B

DG A

Fig. 1

H

E

K

Fig. 2

Fig. 3

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents 10″ Professional Radial Arm Saw General Safety Rules Additional Safety Rules for Radial ARM Saws Extension CordsPower Connections Motor SpecificationsGrounding Instructions Changing Voltage Overload ProtectionUnpacking and Cleaning Functional DescriptionPage Explanation of Operating Controls Assembly Tools Needed for Assembly and AdjustmentAssembling Legs to SAW Base Disconnect Tool from Power Source Removing Blade and Blade Guard from SAWAssembling Adjusting Table Supports Assembling Track ARM Clamp LeverContacts the table board before the motor is fully Track ARM Clamp Handle Y are Adjusting and Checking SAW Blade Travel Square to Fence Assembling Table Board Clamps and Table BoardsPage Checking and Adjusting SAW Blade Square To Table Removing Heeling in SAW Blade CUTAdjusting IN/OUT RIP Scale Assembling Blade and Blade Guard to Machine Tongue on Guard Seats Into Groove of CUTTING-HEADFastening SAW to the Floor Cutting Into Table BoardsON/OFF Switch Adjusting Ball Bearings Against TrackMotor Adjusting Tension on Elevating Column Changing Position of Track ARM Clamping HandleChanging Position of Bevel Clamp Handle Changing Position of Yoke Clamp HandleAdjusting Splitter and ANTI-KICKBACK Fingers Positive Stop Yoke IndexPositive Stop Bevel Index Operations Using a Table ExtensionAuxiliary Table Board Facing CROSS-CUT StopOUT-RIPPING Compound Miter CuttingRipping IN-RIPPINGPushstick Constructing a Push StickPARTS, Service or Warranty Assistance Two Year Limited WarrantyPage Canadian PORTER-CABLE Delta Service Centers
Top Page Image Contents