Black & Decker CS1012 Operation, Removing the Blade, Switch, Kerf Plate Adjustment FIG

Page 8

90511917 CS1012 5/7/07 9:32 AM Page 8

retaining screw (11) by turning the hex wrench (15) counter- clockwise.

•Remove the outer washer.

•Place the saw blade (5) onto the inner

9

15

 

8

 

10

11

flange (16), making sure that the arrow on the blade points in the same direction as the arrow on the tool.

•Fit the outer washer (10) on the spindle.

•Insert the blade retaining screw (11) into the hole in the spindle.

•Prevent spindle rotation by engaging the spanner wrench into the holes of the outer washer.

•Securely tighten the blade retaining screw by holding the spanner wrench and turning hex wrench clockwise to tighten the blade retaining screw.

10

10

11

15

16

5

8

REMOVING THE BLADE

•To prevent spindle rotation, engage the protrusions of the spanner wench (8) into the holes in the outer washer (10).

•Loosen and remove the blade retaining screw (11) by turning it counter- clockwise using the hex wrench (15).

•Remove the outer washer (10).

•Remove the saw blade (5).

WARNING: To reduce the risk of serious personal injury, read, understand and follow all important safety warnings and instructions prior to using tool.

GENERAL CUTS (IMPORTANT: READ SAFETY WARNINGS AND INSTRUCTIONS. )

GUARD AGAINST KICKBACK

With unit unplugged, follow all assembly, adjustment and set up instructions. Make sure lower guard operates. Select the proper blade for the material to be cut.

•Measure and mark work for cutting.

•Support and secure work properly (See Safety Rules and Instructions).

•Use appropriate and required safety equipment (See Safety Rules).

•Secure and maintain work area (See Safety Rules).

•With plug inserted and guard closed, make sure switch turns saw on and off.

WARNING: It is important to support the work properly and to hold the saw firmly to prevent loss of control which could cause personal injury. Figure 3 illustrates recommended hand position.

OPERATION

SWITCH

•To operate the tool, depress the trigger switch (1). The tool will continue to run as long as the trigger is depressed.

•To turn the tool off, release the trigger switch (1). There is no provision for locking the tool on, and the switch should never be locked on by any other means.

KERF PLATE ADJUSTMENT (FIG. 11)

The tool is equipped with a sight guide for straight cutting (22) and for 45° miter cutting (23).

•Be sure the saw is unplugged.

•Adjust the kerf plate as described below.

•Align the left edge of the guides (22) or (23) with the cutting line.

•Keep the kerf plate aligned with the cutting line while sawing.

•Work with the shoe pressed against the workpiece.

ADJUSTING THE KERF PLATE

•Plug in the saw.

•Make a test cut halfway through a piece of scrap wood.

•Withdraw the saw so the cutting line becomes visible.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents 4 185mm Circular Saw VEA EL Español EN LA ContraportadaGeneral Safety Rules Specific Safety Rules Safety Guidelines Definitions Causes and Operator Prevention of KickbackSE These Instructions Additional Safety Rules Circular Saws Lead from lead-based paintsMotor Guard Against KickbackTo Reduce the Risk of Kickback Assembly / Adjustment SET-UP Adjusting the Depth of CUTAdjusting the Bevel Angle FIG Attaching the BladeSwitch Kerf Plate Adjustment FIGAdjusting the Kerf Plate OperationMaintenance SawingHints for Optimum USE Pocket CuttingFull TWO-YEAR Home USE Warranty AccessoriesService Information Mode D’EMPLOI Règles Générales DE Sécurité Zone DE TravailSécurité EN Électricité Lorsque votre corps est mis à la terreRègles DE Sécurité Spécifiques Des évents, car ils couvrent des pièces mobilesUtilisation ET Entretien DE L’OUTIL RéparationPerformances et la sécurité de fonctionnement.V Le plomb contenu dans les peintures à base de plomb Conservez CES DirectivesRégles DE Sécurité Supplémentaires Scies Circulaires PROTÉGEZ-VOUS DES Effets DE Rebond Pour Réduire LE Risque D’EFFET DE RebondMoteur Configuration DE ’ASSEMBLAGE ET DES RéglagesAperçu Général FIG Fonctionnement Accessoires Réglage DE LA Plaque DE RetraitSciage Conseils Pour UNE Utilisation OptimaleInformation SUR LES Réparations » ou composer le numéro suivantProduit et le faire réparer Dans un centre deAutorisé Le disjoncteur est déclenché555326-7100 Normas Generales DE Seguridad InstruccionesÁrea DE Trabajo Seguridad EléctricaNormas DE Seguridad Específicas Posición de encendido, puede propiciar accidentesUSO Y Cuidado DE LA Herramienta MantenimientoCausas DEL Retroceso Y SU Prevención POR Parte DEL Operador Provocarán pérdida del controlConserve Estas Instrucciones Provocar daños en la propiedadPara Reducir EL Riesgo DE Retroceso Peligro Riesgo DE LaceraciónManténgase Alerta Y EN Descripción General FIG ENSAMBLADO/AJUSTECorte mientras la hoja se mueva Ajuste DE LA Profundidad DE Corte YFuncionamiento Aserrado Consejos Para UN USO ÓptimoCorte Interno Almacenamiento DE LA LlaveGarantía Completa DE DOS Años Para USO EN EL Hogar CULIACAN, SIN MONTERREY, N.L GUADALAJARA, JALPUEBLA, PUE MEXICO, D.F

CS1012 specifications

The Black & Decker CS1012 is a powerful and reliable cordless chainsaw that caters to a variety of cutting needs. Designed for both homeowners and DIY enthusiasts, it combines efficiency, ease of use, and innovative technology to deliver outstanding performance in a lightweight package. This model is particularly popular for outdoor tasks such as pruning trees, cutting firewood, and managing landscaping projects.

One of the standout features of the CS1012 is its 12-inch premium Oregon bar and chain, which provides excellent cutting performance and smooth operation. The chainsaw is powered by a robust 20V MAX lithium-ion battery, which offers long runtime and consistent power. This battery technology not only extends the lifespan of the tool but also ensures that users can complete their tasks without frequent interruptions. The lightweight design, weighing only 6.5 pounds, makes it easy to maneuver and reduces user fatigue, allowing for extended usage without discomfort.

The CS1012 incorporates a tool-free chain tensioning system, a significant advantage for users who require quick adjustments while working. This allows for effortless tightening or loosening of the chain, ensuring optimal performance at all times. Additionally, its automatic oiling system helps maintain the chain and bar while in use, promoting longevity and reducing the need for constant maintenance.

Safety is also a priority with the Black & Decker CS1012. It features a chain brake that helps protect the user in case of kickback, along with a two-handed grip for improved stability and control. The transparent oil tank makes it easy for users to monitor oil levels, ensuring they're always prepared before starting their projects.

In summary, the Black & Decker CS1012 is a thoughtfully designed cordless chainsaw that emphasizes power, ease of use, and safety. Its combination of a 12-inch Oregon bar, strong 20V MAX lithium-ion battery, tool-free chain tensioning, and automatic oiling system, make it an ideal choice for anyone looking to tackle outdoor cutting tasks efficiently. As a user-friendly tool, it stands out in the market for its performance and innovative features. Whether you're a seasoned woodworker or a homeowner handling occasional yard work, the CS1012 is an excellent addition to your toolkit.
Top Page Image Contents