Black & Decker CS1012 Sawing, Hints for Optimum USE, Pocket Cutting, Wrench Storage, Maintenance

Page 9

90511917 CS1012 5/7/07 9:32 AM Page 9

While keeping the saw in this position, unplug the saw and loosen the kerf plate on the saw shoe.

Align the 0° mark (22) on the kerf plate with the cutting line. When adjusting for 45° miter cuts, align the 45° mark

(23)on the kerf plate with the cutting

line.

Secure the kerf plate using the screw

11

24

22 23

SAWING

WARNING: To reduce the risk of serious personal injury,always hold the tool with both hands.

Let the blade run freely for a few seconds before starting the cut.

Apply only a gentle pressure to the tool while performing the cut.

Work with the shoe pressed against the workpiece.

HINTS FOR OPTIMUM USE

As some splintering along the line of cut on the top side of the workpiece cannot be avoided, cut on the side where splintering is acceptable.

Where splintering is to be minimized, e.g. when cutting laminates, clamp a piece of plywood onto the top of the workpiece.

POCKET CUTTING (FIG.12)

POCKET CUTTING IS USED TO CUTA HOLE IN APIECE OF MATERIAL WITHOUT CUTTING FROM THE SIDE.

Measure and mark work.

Tilt saw forward and rest front of the shoe on material to be cut. Align so that cut will begin at the back of the drawn rectangle shown in figure 12.

Using the retracting lever, retract blade guard to an upward position, with the blade just clearing the material, start motor and gradually lower the saw into the material.

WARNING: As blade starts cutting the material, release the retracting lever immediately.

Never tie the blade guard in a raised position.

When the shoe rests flat on the material being cut, complete the cut in forward direction.

Allow the blade to come to a complete stop before lifting saw from material.

When starting each new cut, repeat the above steps.

12

WRENCH STORAGE (FIG.13)

The spanner wrench (8) can be stored on the saw shoe as shown in figure 13.

13

8

MAINTENANCE

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid.

IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (other than those listed in this manual) should be performed by authorized service centers or other qualified service organizations, always using identical replacement parts.

LUBRICATION

Black & Decker tools are properly lubricated at the factory and are ready for use.

9

Image 9
Contents VEA EL Español EN LA Contraportada 4 185mm Circular SawGeneral Safety Rules Specific Safety Rules Causes and Operator Prevention of Kickback Safety Guidelines DefinitionsLead from lead-based paints SE These Instructions Additional Safety Rules Circular SawsGuard Against Kickback To Reduce the Risk of KickbackMotor Adjusting the Depth of CUT Assembly / Adjustment SET-UPAdjusting the Bevel Angle FIG Attaching the BladeKerf Plate Adjustment FIG SwitchAdjusting the Kerf Plate OperationSawing MaintenanceHints for Optimum USE Pocket CuttingAccessories Service InformationFull TWO-YEAR Home USE Warranty Mode D’EMPLOI Zone DE Travail Règles Générales DE SécuritéSécurité EN Électricité Lorsque votre corps est mis à la terreDes évents, car ils couvrent des pièces mobiles Règles DE Sécurité SpécifiquesUtilisation ET Entretien DE L’OUTIL RéparationPerformances et la sécurité de fonctionnement.V Conservez CES Directives Régles DE Sécurité Supplémentaires Scies CirculairesLe plomb contenu dans les peintures à base de plomb Pour Réduire LE Risque D’EFFET DE Rebond PROTÉGEZ-VOUS DES Effets DE RebondConfiguration DE ’ASSEMBLAGE ET DES Réglages Aperçu Général FIGMoteur Fonctionnement Réglage DE LA Plaque DE Retrait AccessoiresSciage Conseils Pour UNE Utilisation Optimale» ou composer le numéro suivant Information SUR LES RéparationsDans un centre de Produit et le faire réparerAutorisé Le disjoncteur est déclenché555326-7100 Instrucciones Normas Generales DE SeguridadÁrea DE Trabajo Seguridad EléctricaPosición de encendido, puede propiciar accidentes Normas DE Seguridad EspecíficasUSO Y Cuidado DE LA Herramienta MantenimientoProvocarán pérdida del control Causas DEL Retroceso Y SU Prevención POR Parte DEL OperadorProvocar daños en la propiedad Conserve Estas InstruccionesPeligro Riesgo DE Laceración Manténgase Alerta Y ENPara Reducir EL Riesgo DE Retroceso ENSAMBLADO/AJUSTE Descripción General FIGCorte mientras la hoja se mueva Ajuste DE LA Profundidad DE Corte YFuncionamiento Consejos Para UN USO Óptimo AserradoCorte Interno Almacenamiento DE LA LlaveGarantía Completa DE DOS Años Para USO EN EL Hogar GUADALAJARA, JAL CULIACAN, SIN MONTERREY, N.LPUEBLA, PUE MEXICO, D.F

CS1012 specifications

The Black & Decker CS1012 is a powerful and reliable cordless chainsaw that caters to a variety of cutting needs. Designed for both homeowners and DIY enthusiasts, it combines efficiency, ease of use, and innovative technology to deliver outstanding performance in a lightweight package. This model is particularly popular for outdoor tasks such as pruning trees, cutting firewood, and managing landscaping projects.

One of the standout features of the CS1012 is its 12-inch premium Oregon bar and chain, which provides excellent cutting performance and smooth operation. The chainsaw is powered by a robust 20V MAX lithium-ion battery, which offers long runtime and consistent power. This battery technology not only extends the lifespan of the tool but also ensures that users can complete their tasks without frequent interruptions. The lightweight design, weighing only 6.5 pounds, makes it easy to maneuver and reduces user fatigue, allowing for extended usage without discomfort.

The CS1012 incorporates a tool-free chain tensioning system, a significant advantage for users who require quick adjustments while working. This allows for effortless tightening or loosening of the chain, ensuring optimal performance at all times. Additionally, its automatic oiling system helps maintain the chain and bar while in use, promoting longevity and reducing the need for constant maintenance.

Safety is also a priority with the Black & Decker CS1012. It features a chain brake that helps protect the user in case of kickback, along with a two-handed grip for improved stability and control. The transparent oil tank makes it easy for users to monitor oil levels, ensuring they're always prepared before starting their projects.

In summary, the Black & Decker CS1012 is a thoughtfully designed cordless chainsaw that emphasizes power, ease of use, and safety. Its combination of a 12-inch Oregon bar, strong 20V MAX lithium-ion battery, tool-free chain tensioning, and automatic oiling system, make it an ideal choice for anyone looking to tackle outdoor cutting tasks efficiently. As a user-friendly tool, it stands out in the market for its performance and innovative features. Whether you're a seasoned woodworker or a homeowner handling occasional yard work, the CS1012 is an excellent addition to your toolkit.