Bosch Power Tools 1591EVS, 1590EVS manual Power Tool Safety Rules, Work Area

Page 2

 

 

Power Tool Safety Rules

 

 

Read and understand all instructions. Failure to follow all instructions

 

! WARNING

 

 

listed below, may result in electric shock, fire and/or serious personal injury.

 

 

 

 

SAVE THESE INSTRUCTIONS

Work Area

Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.

Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.

Keep by-standers, children, and visitors away while operating a power tool. Distractions can cause you to lose control.

Electrical Safety

Double Insulated tools are equipped with a polarized plug (one blade is wider than the other.) This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any way. Double Insulation eliminates the need for the three wire grounded power cord and grounded power supply system. Before plugging in the tool, be certain the outlet voltage supplied is within the voltage marked on the nameplate. Do not use “AC only” rated tools with a DC power supply.

Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. If operating the power tool in damp locations is unavoidable, a Ground Fault Circuit Interrupter must be used to supply the power to your tool. Electrician’s rubber gloves and footwear will further enhance your personal safety.

Don't expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock.

When operating a power tool outside, use an outdoor extension cord marked "W-A" or "W." These cords are rated for outdoor use and reduce the risk of electric shock. Refer to “Recommended sizes of Extension Cords” in the Accessory section of this manual.

Personal Safety

Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.

Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts. Keep handles dry, clean and free from oil and grease.

Avoid accidental starting. Be sure switch is “OFF” before plugging in. Carrying tools with your finger on the switch or plugging in tools that have the switch “ON” invites accidents.

Remove adjusting keys or wrenches before turning the tool “ON”. A wrench or a key that is left attached to a rotating part of the tool may result in personal injury.

Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations.

Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing protection must be used for appropriate conditions.

Tool Use and Care

Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control.

-2-

Image 2
Contents Importante Power Tool Safety Rules Work AreaSafety Rules for Jigsaws ServicePage Symbols Functional Description and Specifications JigsawsDust Extraction AssemblyPrecision Control Attaching NON-MARRING Overshoe ANTI-SPLINTER InsertPlunger Speed Trigger Switch with LOCK-ON ButtonOperating Instructions Variable Speed DialFootplate Angle Adjustment Blower Switched onBlower Switched OFF Chip BlowerParallel Cutting Plunge CuttingCircle and Parallel Cutting Guide Circle CuttingTool Lubrication MaintenanceAccessories Carbon BrushesRègles de Sécurité Générales Conservez CES InstructionsRègles de sécurité concernant les scies sauteuses RéparationLe plomb provenant des peintures à base de plomb Symboles Description fonctionnelle et spécifications Scies sauteusesPose ET Dépose DE LA Lame Non compris, disponible en accessoireAssemblage Renforcement DE LA PrécisionPose DE LA Sursemelle QUI Nabîme PAS Insert ANTI-ÉCLATSConsignes de fonctionnement SOUFFLE-COPEAUX À Larrêt SOUFFLE-COPEAUXSOUFFLE-COPEAUX EN Marche Réglage DE Langle DE LA SemelleDécoupage DE Cercles Coupe EN PlongéeSciage Parallèle Lubrification DE L’OUTIL AccessoiresEntretien Balais OU CharbonsUtilice abrazaderas u otro modo práctico de fijar y Normas de seguridad para herramientas mecánicasConserve Estas Instrucciones Normas de seguridad para sierras de vaivén ServicioPage Símbolos De Ni-CdDescripción funcional y especificaciones Sierras caladorasControl DE Precisión EnsamblajeInstalación Y Remoción DE LA Hoja Extracción DE PolvoColocacion DE LA Sobrezapata Antiindentaciones Accesorio DE Insercion AntiastillasInstrucciones de funcionamiento Soplador Apagado Soplador DE VirutasSoplador Encendido Corte AL RASCortes EN Círculo Corte Mediante Descenso VerticalParallel Cutting Lubricación DE LAS Herramientas MantenimientoAccesorios Escobillas DE CarbónRemarques Notas Limited Warranty of Bosch Portable and Benchtop Power Tools