Craftsman 315.22839 Assemblingtable Extensions, HEX Headbolt Flat, Aligning Table Extensions

Page 20

ASSEMBLINGTABLE EXTENSIONS

See Figure 10.

•Locate the tame extensions and the sma(I hard- ware bag with the following:

8 hex bolts (5/16-18 x 1-1/4 in.' 8 hex nuts (5/16-18)

16 flat washers (5/16 in.)

,_ WARNING: The table extensions not only provide a support for large or wide pieces of

material, but help protect you. Serious injury can result from workpiece binding or kickback due to twisted rails or a misaligned rip fence.

•With the saw upside down, align table extensions to the saw table. Put a flat washer on each bolt, and attach the extensions to the table by inserting bolts through holes from the direction of the table.

•Slip the remaining flat washers and hex nuts on the bolts. Lightly tighten with a 12 mm wrench.

TABLE

EXTENSION

HEX

HEADBOLT

FLAT

WASHER

HEXNUT

Fig. 10

•Get help to stand saw assembly upright using the center saw table. Do not grasp saw by extensions.

,_, WARNING: Do not lift the saw table without

u

help. Hold it close to your body. Keep your knees bent and lift with your legs, not your back. Ignoring these precautions can result in back injury.

ALIGNING TABLE EXTENSIONS

See Figure 11.

A good alignment allows the rails to slide on easily.

•Stand at the front of the saw and line up the front edges of the saw table and extensions.

•Pull the extensions out slightly, put a block of wood where the extension meets the table, and tap the block of wood with a hammer. Check and repeat until the front edges are even.

•Lift each extension slightly until it is higher than table (if necessary, place a block below and tap upward). Center the block of wood over the front and rear edges and tap it until both are even (flush) with saw table. Recheck the front alignment. If even, tighten the screws with a 12 mm wrench.

BLOCKTABLE

OF WOOD EXTENSION

BLOCK

FRONT OFFRONT OF OF WOOD

SAW TABLE TABLE EXTENSION

 

 

 

TAP

 

 

 

HERE

 

BLOCK

TAP

TOP OF TABLE

TOP OF

OFWOOD

HERE

EXTENSION

 

 

SAW TABLE

 

!

 

 

 

 

Fig. 11

SPLIT RAIL DESIGN

Your saw has a split rail design. The front and rear rails each have a left and right piece that must be installed. They are joined together on your saw with a connector. We suggest that you install the right rear and right front pieces first. Align and secure these pieces, then use the connectors provided to secure left rear and left front pieces.

rRRFTSMRN*TABLE SAW 315.228390

2O

Page 19 Page 21
Image 20
Page 19 Page 21
Contents IIRRFrSMRN Full ONE Year Warranty on Craftsman Table SAW 30-34 Symbol Meaning Safety Alert SymbolRules for Safe Operation Do not Feed the Material TOO Speed and Wiring Extension CordsElectrical Connection Grounding InstructionsRRRFTSMRH TABLESAW315.228390 Assemble all parts to your saw before connecting It to power supply. Saw should never beConnected to power supply when you are Assembling parts, making adjustments, installingBelt Guard Blade Guard Assembly Hardware Screw#10-24x 1/2in Clip End cap for rear rail Cord Screw #8-32 x 1/2 Framingsquare NutdriverCombinationsquare Hammer 45TRIANGLE Inch Table Saw CRRFTSMRNTABLESAW315.22839014IorDo ExtensionNotLiftSawTablesWith. Rails Push OffoiScalehandle Height HandwheelLEG Stand Beltcover Levelingfoot Motor Bevel LockhandleOverview Installing Handwheels on Table SAW Base Bevel Handwheel HeightUpperbracewasher Hexnut Carriage Bolt LEGMounting the LEG Stand on the Table SAW Base Legstand FlatwasherAssemblingtable Extensions HEX Headbolt FlatAligning Table Extensions Split Rail DesignHEX NUT Rearrail Connector EndcapSee Figures 12 NUT HE BOLT8Front Rail SAW Tabletable ExtensionAssembly Aligning the RIP Fence and Front RailSee Figures 17 RIP Fence Hook OverSAW Pulley Belt BeltguardChecking the Throat Plate Hexkeyframingsquare ThroatplateInstalling BladeBlade Guard Bracket Lock HEXSee Figures 26 Rivingknife BladeRivingknife Blade Throat Plate Framing Blade JFraming Square Miter Gage GrooveAlignment See Figures 31Miter Gage Groove Blade RIP Fence FramingChecking Squareness of Extension Tables to SAW Table SquareSawtable Extension Square SawtableReplacing the Blade See Figures 35Blade Guard To Loosen Blade NUT Blade BlaiwasherBLADEGUARD18NOTSHOWNFORCLARITY AT Front NUT I Markedtooth BladeSee Figures 38 MitergagegrooveHexkey Sawtableview Frombelow Rearsaw Table TablebracketSee Figures 41 Indicator Adjusting the Miter Gage 8TOP 8CREW AdjustableMiterknob Gage ROD Miter 8TOP 8CREWRemoving Replacing the Throat Throatplate PlateKEY 8LOT SpringclipAvoiding Kickback PUSHSTICK8Types of Cuts See Figures 47 PLACELEFTHANDONWHENMITERGAGE18Mitergagehereplacerighthandon Mitergageknobhere Making a RIP CUTRIP CUT Making a Miter CUTMiter CUT Blade Mitergage Straight Angled Bevel Handwheel HeightScale Blade Bevelcrosscut BladeBevel Ripcut Placelefthandon Mitergagehere Mitergageknobhere Making a Compound Bevel Miter CUTOnworkpieceand Making a Large Panel CUT Making a NON-THROUGH CUTLargepanelcut RIP Fence NON-THROUGHCUT Pushstick Guard BladeMaking a Dado CUT Dadocut Frontof SAW General MaintenanceMotor / Electrical Problem Cause Solution See Heeling Sawblade Adjustments Setting Bevel StopsIndicator Adjustments See Aligning Rip FenceFront Rail in the Assembly Fence. See Aligning Rip Fence£RRFTSMRN Table SAW Figure a Parts List for Figure a KEY PartNO. Number DescriptionCraftsman Table SAW- Model no Parts List for Figure B KEY Part NO. NumberCraftsman Table SAW Model no Description Qljan Parts List for Figure CKEY Part NO. Number Figured Parts List for Figure D KEY Part NumberFiguree Parts List for Figure E Figuref Parts List for Figure F Figureg Parts List for Figure G Figureh Parts List for Figure H Figurei Parts List for Figure Description QuanAu Canadapourserviceen franais

315.22839 specifications

The Craftsman 315.22839 is a versatile and reliable power tool that has gained popularity among DIY enthusiasts and professionals alike. Known for its robust construction and user-friendly features, this electric tool is perfect for a variety of tasks, from sanding and drilling to cutting.

One of the main features of the Craftsman 315.22839 is its powerful motor. Equipped with a reliable engine, it delivers impressive torque and speed, making it capable of tackling demanding projects. The tool boasts adjustable speed settings which allow users to customize the tool's performance based on the task at hand. This feature not only enhances precision but also promotes efficiency as users can switch speeds for different materials and applications.

Another standout attribute of the Craftsman 315.22839 is its ergonomic design. It has a comfortable grip that minimizes hand fatigue during extended use, ensuring that users can work longer and more efficiently. Additionally, the lightweight construction of the tool allows for easy maneuverability, making it ideal for both intricate and large-scale jobs.

The Craftsman 315.22839 also integrates advanced safety features. It includes a safety lock switch that prevents accidental startups, a crucial aspect for ensuring user safety during operation. The durable housing is designed to withstand the rigors of heavy usage, ensuring longevity and reliability in various work environments.

Versatility is a hallmark of the Craftsman brand, and the 315.22839 is no exception. It is compatible with a range of attachments and accessories, allowing users to switch between different functionalities. Whether you’re drilling into wood, cutting through metal, or sanding surfaces, the adaptable nature of this tool makes it a valuable addition to any toolbox.

In terms of technology, Craftsman has incorporated innovative engineering techniques to enhance the performance and durability of the 315.22839. Features like heat-resistant materials and advanced cooling systems ensure that the tool can operate under strenuous conditions without overheating or losing efficiency.

Overall, the Craftsman 315.22839 stands out in the crowded market of power tools. Its combination of power, efficiency, and user-friendly design makes it an excellent choice for both novice and experienced users looking for reliable performance. Whether you are embarking on a home improvement project or tackling a professional job, the 315.22839 is equipped to deliver results that meet your expectations.
Top Page Image Contents