Craftsman 315.22839 Removing Replacing the Throat Throatplate, Plate, KEY 8LOT, Springclip, Top

Page 34

REMOVING

/

REPLACING THE THROAT

THROATPLATE

PLATE

 

 

 

See Figure

44.

 

KEY 8LOT_

,_k WARNING:

Make sure the switch is off, the

 

switch key is removed, and your saw is unplugged. Failure to do so could result in accidental starting, resulting in serious personal injury.

•To remove the throat plate, first loosen the screw in the throat plate with a phillips screwdriver and lift the front end. Pull it out toward the front of the saw.

•To re-install the throat plate, place it in the opening. Push it toward the rear of saw base to engage the spring clip.

Note: The keyslot in the throat plate will drop over the screw.

•Check that the throat plate is even with the table top. If not, adjust the four set screws with a 2 mm hex key. See the procedure in the Assem- bly section.

•Securely tighten throat plate screw. Do not allow the throat plate to bow up above the table surface.

SPRINGCLIP

TABLE

TOP

Fig. 44

CRRFTSMRN° TABLESAW 315.22839034

Page 33 Page 35
Image 34
Page 33 Page 35
Contents IIRRFrSMRN Full ONE Year Warranty on Craftsman Table SAW 30-34 Symbol Meaning Safety Alert SymbolRules for Safe Operation Do not Feed the Material TOO Electrical Connection Speed and WiringExtension Cords Grounding InstructionsRRRFTSMRH TABLESAW315.228390 Connected to power supply when you are Assemble all parts to your saw before connectingIt to power supply. Saw should never be Assembling parts, making adjustments, installingBelt Guard Blade Guard Assembly Hardware Screw#10-24x 1/2in Clip End cap for rear rail Cord Screw #8-32 x 1/2 Combinationsquare Hammer 45TRIANGLE NutdriverFramingsquare Inch Table Saw CRRFTSMRNTABLESAW315.22839014IorDo ExtensionNotLiftSawTablesWith. Rails Push OffoiLEG Stand ScalehandleHeight Handwheel Beltcover Levelingfoot Motor Bevel LockhandleOverview Upperbracewasher Hexnut Carriage Bolt Installing Handwheels on Table SAW BaseBevel Handwheel Height LEGMounting the LEG Stand on the Table SAW Base Legstand FlatwasherAligning Table Extensions Assemblingtable ExtensionsHEX Headbolt Flat Split Rail DesignSee Figures 12 Rearrail Connector EndcapHEX NUT Front Rail NUTHE BOLT8 SAW Tabletable ExtensionSee Figures 17 AssemblyAligning the RIP Fence and Front Rail RIP Fence Hook OverChecking the Throat Plate SAW PulleyBelt Beltguard Hexkeyframingsquare ThroatplateBlade Guard Bracket Lock InstallingBlade HEXRivingknife Blade Throat Plate Framing See Figures 26Rivingknife Blade Blade JFraming Square Miter Gage GrooveMiter Gage Groove Blade AlignmentSee Figures 31 RIP Fence FramingSawtable Checking Squareness of Extension Tables to SAW TableSquare Extension Square SawtableBlade Guard To Loosen Blade NUT Replacing the BladeSee Figures 35 Blade BlaiwasherSee Figures 38 BLADEGUARD18NOTSHOWNFORCLARITYAT Front NUT I Markedtooth Blade MitergagegrooveSee Figures 41 Sawtableview Frombelow Rearsaw Table TablebracketHexkey Miterknob Gage ROD Miter Indicator Adjusting the Miter Gage8TOP 8CREW Adjustable 8TOP 8CREWKEY 8LOT Removing Replacing the Throat ThroatplatePlate SpringclipAvoiding Kickback PUSHSTICK8Types of Cuts Mitergagehereplacerighthandon Mitergageknobhere See Figures 47PLACELEFTHANDONWHENMITERGAGE18 Making a RIP CUTMiter CUT RIP CUTMaking a Miter CUT Blade Mitergage Straight Angled Bevel Handwheel HeightBevel Ripcut Bevelcrosscut BladeScale Blade Onworkpieceand Making a Compound Bevel Miter CUTPlacelefthandon Mitergagehere Mitergageknobhere Largepanelcut RIP Fence Making a Large Panel CUTMaking a NON-THROUGH CUT NON-THROUGHCUT Pushstick Guard BladeMaking a Dado CUT Dadocut Motor / Electrical General MaintenanceFrontof SAW Problem Cause Solution Indicator Adjustments See Heeling Sawblade AdjustmentsSetting Bevel Stops See Aligning Rip FenceFront Rail in the Assembly Fence. See Aligning Rip Fence£RRFTSMRN Table SAW Figure a NO. Number Parts List for Figure aKEY Part DescriptionCraftsman Table SAW- Model no Parts List for Figure B KEY Part NO. NumberCraftsman Table SAW Model no KEY Part NO. Number Parts List for Figure CDescription Qljan Figured Parts List for Figure D KEY Part NumberFiguree Parts List for Figure E Figuref Parts List for Figure F Figureg Parts List for Figure G Figureh Parts List for Figure H Figurei Parts List for Figure Description QuanAu Canadapourserviceen franais

315.22839 specifications

The Craftsman 315.22839 is a versatile and reliable power tool that has gained popularity among DIY enthusiasts and professionals alike. Known for its robust construction and user-friendly features, this electric tool is perfect for a variety of tasks, from sanding and drilling to cutting.

One of the main features of the Craftsman 315.22839 is its powerful motor. Equipped with a reliable engine, it delivers impressive torque and speed, making it capable of tackling demanding projects. The tool boasts adjustable speed settings which allow users to customize the tool's performance based on the task at hand. This feature not only enhances precision but also promotes efficiency as users can switch speeds for different materials and applications.

Another standout attribute of the Craftsman 315.22839 is its ergonomic design. It has a comfortable grip that minimizes hand fatigue during extended use, ensuring that users can work longer and more efficiently. Additionally, the lightweight construction of the tool allows for easy maneuverability, making it ideal for both intricate and large-scale jobs.

The Craftsman 315.22839 also integrates advanced safety features. It includes a safety lock switch that prevents accidental startups, a crucial aspect for ensuring user safety during operation. The durable housing is designed to withstand the rigors of heavy usage, ensuring longevity and reliability in various work environments.

Versatility is a hallmark of the Craftsman brand, and the 315.22839 is no exception. It is compatible with a range of attachments and accessories, allowing users to switch between different functionalities. Whether you’re drilling into wood, cutting through metal, or sanding surfaces, the adaptable nature of this tool makes it a valuable addition to any toolbox.

In terms of technology, Craftsman has incorporated innovative engineering techniques to enhance the performance and durability of the 315.22839. Features like heat-resistant materials and advanced cooling systems ensure that the tool can operate under strenuous conditions without overheating or losing efficiency.

Overall, the Craftsman 315.22839 stands out in the crowded market of power tools. Its combination of power, efficiency, and user-friendly design makes it an excellent choice for both novice and experienced users looking for reliable performance. Whether you are embarking on a home improvement project or tackling a professional job, the 315.22839 is equipped to deliver results that meet your expectations.
Top Page Image Contents