Craftsman 315.22839 Sawtableview Frombelow Rearsaw Table Tablebracket, See Figures 41, Hexkey

Page 32

•If the blade was too close to the miter gage groove, back the bracket away with the block of wood and hammer.

•Tighten the screws, raise the blade and recheck.

•Repeat until blade is parallel to miter gage groove.

•If the blade is not parallel, adjust the front table bracket. Tilt the blade to 45 ° with the blade lock handle and bevel handwheel.

•From the back of the saw, loosen the bolts holding the front table bracket, as well as the rear table bracket.

•Reposition the blade to 90° with the bevel hand- wheel and blade lock handle.

•Lower the blade and move the brackets as needed. Retighten all bracket screws.

•Raise the blade and recheck. Repeat until the blade is parallel to the miter gage groove.

•Place the throat plate in the opening and push it toward the rear of saw base to engage the spring clip.

Note: The keyslot in the throat plate will drop over the front screw.

•Tighten the screw. Do not allow the throat plate to bow up above the table surface.

SAWTABLEVIEW FROMBELOW

REARSAW TABLE

TABLEBRACKET/

 

FRONTj

 

FRONT

BRACKET

 

TABLEBRACKET

SCREW(S)

Fig. 40

SETTING THE BEVEL STOPS AND INDICATOR

See Figures 41 and 42.

_ WARNING: Make sure the switch is off, the switch key is removed, and your saw is

unplugged. Failure to do so could result in accidental starting, resulting in serious personal injury.

The bevel scale should show 0° when the blade is set vertical at 90° to table, and 45° when blade is at 45 ° tilt.

•Raise the blade all the way up by turning the height handwheel. Lift the blade guard.

•Loosen bevel lock handle and turn the bevel handwheel clockwise to tilt the blade. Reverse it and turn the handwheel counterclockwise until it stops.

•Check the blade angle with a combination square.

Don'tlet the square touch a blade tooth. The blade should be at 90 ° and the scale indicator at 0°.

Note: The scale indicator is the plastic plate on the scale at the front of the cabinet.

•If the scale indicator does not point to 0°, loosen the scale indicator with a screwdriver, adjust it within the slot, and retighten the screw.

•If the blade angle is wrong, adjust the 90° stop screw (left of the blade, looking from the front). Start by turning the 90° stop screw three or four turns with a 4 mm hex key.

90oSTOPSCREW

45oSTOPSCREW

4mm

HEXKEY

Fig. 41

•Turn the bevel handwheel clockwise once, then back counterclockwise to square blade with table.

•Tighten the 90° stop screw and recheck that the blade is square in a 90° position. If not, repeat. When the blade is square, check the scale indica- tor. tf it is not at zero, reset the scale indicator as before.

CRRFTSMI_N° TABLESAW 315.22839032

Page 31 Page 33
Image 32
Page 31 Page 33
Contents IIRRFrSMRN Full ONE Year Warranty on Craftsman Table SAW 30-34 Symbol Meaning Safety Alert SymbolRules for Safe Operation Do not Feed the Material TOO Speed and Wiring Extension CordsElectrical Connection Grounding InstructionsRRRFTSMRH TABLESAW315.228390 Assemble all parts to your saw before connecting It to power supply. Saw should never beConnected to power supply when you are Assembling parts, making adjustments, installingBelt Guard Blade Guard Assembly Hardware Screw#10-24x 1/2in Clip End cap for rear rail Cord Screw #8-32 x 1/2 Framingsquare NutdriverCombinationsquare Hammer 45TRIANGLE Inch Table Saw CRRFTSMRNTABLESAW315.22839014IorDo ExtensionNotLiftSawTablesWith. Rails Push OffoiScalehandle Height HandwheelLEG Stand Beltcover Levelingfoot Motor Bevel LockhandleOverview Installing Handwheels on Table SAW Base Bevel Handwheel HeightUpperbracewasher Hexnut Carriage Bolt LEGMounting the LEG Stand on the Table SAW Base Legstand FlatwasherAssemblingtable Extensions HEX Headbolt FlatAligning Table Extensions Split Rail DesignHEX NUT Rearrail Connector EndcapSee Figures 12 NUT HE BOLT8Front Rail SAW Tabletable ExtensionAssembly Aligning the RIP Fence and Front RailSee Figures 17 RIP Fence Hook OverSAW Pulley Belt BeltguardChecking the Throat Plate Hexkeyframingsquare ThroatplateInstalling BladeBlade Guard Bracket Lock HEXSee Figures 26 Rivingknife BladeRivingknife Blade Throat Plate Framing Blade JFraming Square Miter Gage GrooveAlignment See Figures 31Miter Gage Groove Blade RIP Fence FramingChecking Squareness of Extension Tables to SAW Table SquareSawtable Extension Square SawtableReplacing the Blade See Figures 35Blade Guard To Loosen Blade NUT Blade BlaiwasherBLADEGUARD18NOTSHOWNFORCLARITY AT Front NUT I Markedtooth BladeSee Figures 38 MitergagegrooveHexkey Sawtableview Frombelow Rearsaw Table TablebracketSee Figures 41 Indicator Adjusting the Miter Gage 8TOP 8CREW AdjustableMiterknob Gage ROD Miter 8TOP 8CREWRemoving Replacing the Throat Throatplate PlateKEY 8LOT SpringclipAvoiding Kickback PUSHSTICK8Types of Cuts See Figures 47 PLACELEFTHANDONWHENMITERGAGE18Mitergagehereplacerighthandon Mitergageknobhere Making a RIP CUTRIP CUT Making a Miter CUTMiter CUT Blade Mitergage Straight Angled Bevel Handwheel HeightScale Blade Bevelcrosscut BladeBevel Ripcut Placelefthandon Mitergagehere Mitergageknobhere Making a Compound Bevel Miter CUTOnworkpieceand Making a Large Panel CUT Making a NON-THROUGH CUTLargepanelcut RIP Fence NON-THROUGHCUT Pushstick Guard BladeMaking a Dado CUT Dadocut Frontof SAW General MaintenanceMotor / Electrical Problem Cause Solution See Heeling Sawblade Adjustments Setting Bevel StopsIndicator Adjustments See Aligning Rip FenceFront Rail in the Assembly Fence. See Aligning Rip Fence£RRFTSMRN Table SAW Figure a Parts List for Figure a KEY PartNO. Number DescriptionCraftsman Table SAW- Model no Parts List for Figure B KEY Part NO. NumberCraftsman Table SAW Model no Description Qljan Parts List for Figure CKEY Part NO. Number Figured Parts List for Figure D KEY Part NumberFiguree Parts List for Figure E Figuref Parts List for Figure F Figureg Parts List for Figure G Figureh Parts List for Figure H Figurei Parts List for Figure Description QuanAu Canadapourserviceen franais

315.22839 specifications

The Craftsman 315.22839 is a versatile and reliable power tool that has gained popularity among DIY enthusiasts and professionals alike. Known for its robust construction and user-friendly features, this electric tool is perfect for a variety of tasks, from sanding and drilling to cutting.

One of the main features of the Craftsman 315.22839 is its powerful motor. Equipped with a reliable engine, it delivers impressive torque and speed, making it capable of tackling demanding projects. The tool boasts adjustable speed settings which allow users to customize the tool's performance based on the task at hand. This feature not only enhances precision but also promotes efficiency as users can switch speeds for different materials and applications.

Another standout attribute of the Craftsman 315.22839 is its ergonomic design. It has a comfortable grip that minimizes hand fatigue during extended use, ensuring that users can work longer and more efficiently. Additionally, the lightweight construction of the tool allows for easy maneuverability, making it ideal for both intricate and large-scale jobs.

The Craftsman 315.22839 also integrates advanced safety features. It includes a safety lock switch that prevents accidental startups, a crucial aspect for ensuring user safety during operation. The durable housing is designed to withstand the rigors of heavy usage, ensuring longevity and reliability in various work environments.

Versatility is a hallmark of the Craftsman brand, and the 315.22839 is no exception. It is compatible with a range of attachments and accessories, allowing users to switch between different functionalities. Whether you’re drilling into wood, cutting through metal, or sanding surfaces, the adaptable nature of this tool makes it a valuable addition to any toolbox.

In terms of technology, Craftsman has incorporated innovative engineering techniques to enhance the performance and durability of the 315.22839. Features like heat-resistant materials and advanced cooling systems ensure that the tool can operate under strenuous conditions without overheating or losing efficiency.

Overall, the Craftsman 315.22839 stands out in the crowded market of power tools. Its combination of power, efficiency, and user-friendly design makes it an excellent choice for both novice and experienced users looking for reliable performance. Whether you are embarking on a home improvement project or tackling a professional job, the 315.22839 is equipped to deliver results that meet your expectations.
Top Page Image Contents