Craftsman 315.22839 owner manual See Figures 12, Rearrail Connector Endcap, Hex Nut

Page 21

Note:Therightsideof sawison yourrightwhen facingthesaw,asif youwerein normal

operatingposition.

INSTALLINGTHEREARRAIL

See Figures 12- 14.

,4_ WARNING: Front and rear rails must be installed and carefully aligned to reduce the risk

of kickback. Kickback can result in serious injury.

•From the carton, remove the rear rail pieces and the following hardware:

6 square head bolts (5/16-18 x 1 in.) 6 fiat washers (5/16 in.)

6 hex nuts (5/16-18) Rear rail connector

Right and left end caps for rear rail 2 screws (#8-32 x 1/2 in.)

Note: Remaining hardware from this hardware bag is used for installing the front rail and end caps.

•At the back of the table, put the square head bolts

in the holes in the edge of the saw table and the outer holes in each extension table so the bolt

heads extend outward 1/2 in.

•Under the table, loosely attach washers and hex nuts onto bolts. Slide the slot on the rear rail over

the bolts. Adjust each bolt to fit the rail closely to the table.

•Position right rail (longest piece) so that right hand edge extends 2-1/2 inches beyond table extension.

•Push right rail against table and tighten each nut with a 12 mm wrench, tf rail jams and does not slide easily over bolts, re-align table extensions.

•Put the end caps on rail ends. Insert the screws and tighten with a phillips head screwdriver.

TABLE

8LOTEXTEN810N

REAR RAIL

8QUARE

WA8HER

TABLE

REARRAIL

REARRAIL

 

CONNECTOR

Fig. 13

2-1/2 in,

ENDCAP

REARRAIL

8CREW

REAROF 8AW

Fig. 14

8QUARE

 

HEX NUT

HEADBOLT8

FLAT

 

 

WA8HER

Fig. 12

21

rRRFTSMRN°TABLE SAW315.228390

Page 20 Page 22
Image 21
Page 20 Page 22
Contents IIRRFrSMRN Full ONE Year Warranty on Craftsman Table SAW 30-34 Safety Alert Symbol Symbol MeaningRules for Safe Operation Do not Feed the Material TOO Extension Cords Speed and WiringElectrical Connection Grounding InstructionsRRRFTSMRH TABLESAW315.228390 It to power supply. Saw should never be Assemble all parts to your saw before connectingConnected to power supply when you are Assembling parts, making adjustments, installingBelt Guard Blade Guard Assembly Hardware Screw#10-24x 1/2in Clip End cap for rear rail Cord Screw #8-32 x 1/2 Nutdriver Combinationsquare Hammer 45TRIANGLEFramingsquare CRRFTSMRNTABLESAW315.22839014 Inch Table SawPush Offoi IorDo ExtensionNotLiftSawTablesWith. RailsHeight Handwheel ScalehandleLEG Stand Beltcover Levelingfoot Motor Bevel LockhandleOverview Bevel Handwheel Height Installing Handwheels on Table SAW BaseUpperbracewasher Hexnut Carriage Bolt LEGLegstand Flatwasher Mounting the LEG Stand on the Table SAW BaseHEX Headbolt Flat Assemblingtable ExtensionsAligning Table Extensions Split Rail DesignRearrail Connector Endcap See Figures 12HEX NUT HE BOLT8 NUTFront Rail SAW Tabletable ExtensionAligning the RIP Fence and Front Rail AssemblySee Figures 17 RIP Fence Hook OverBelt Beltguard SAW PulleyChecking the Throat Plate Hexkeyframingsquare ThroatplateBlade InstallingBlade Guard Bracket Lock HEXRivingknife Blade See Figures 26Rivingknife Blade Throat Plate Framing Blade JMiter Gage Groove Framing SquareSee Figures 31 AlignmentMiter Gage Groove Blade RIP Fence FramingSquare Checking Squareness of Extension Tables to SAW TableSawtable Extension Square SawtableSee Figures 35 Replacing the BladeBlade Guard To Loosen Blade NUT Blade BlaiwasherAT Front NUT I Markedtooth Blade BLADEGUARD18NOTSHOWNFORCLARITYSee Figures 38 MitergagegrooveSawtableview Frombelow Rearsaw Table Tablebracket See Figures 41Hexkey 8TOP 8CREW Adjustable Indicator Adjusting the Miter GageMiterknob Gage ROD Miter 8TOP 8CREWPlate Removing Replacing the Throat ThroatplateKEY 8LOT SpringclipPUSHSTICK8 Avoiding KickbackTypes of Cuts PLACELEFTHANDONWHENMITERGAGE18 See Figures 47Mitergagehereplacerighthandon Mitergageknobhere Making a RIP CUTMaking a Miter CUT RIP CUTMiter CUT Blade Mitergage Straight Angled Bevel Handwheel HeightBevelcrosscut Blade Bevel RipcutScale Blade Making a Compound Bevel Miter CUT OnworkpieceandPlacelefthandon Mitergagehere Mitergageknobhere Making a NON-THROUGH CUT Making a Large Panel CUTLargepanelcut RIP Fence NON-THROUGHCUT Pushstick Guard BladeMaking a Dado CUT Dadocut General Maintenance Motor / ElectricalFrontof SAW Problem Cause Solution Setting Bevel Stops See Heeling Sawblade AdjustmentsIndicator Adjustments See Aligning Rip FenceFence. See Aligning Rip Fence Front Rail in the Assembly£RRFTSMRN Table SAW Figure a KEY Part Parts List for Figure aNO. Number DescriptionCraftsman Table SAW- Model no KEY Part NO. Number Parts List for Figure BCraftsman Table SAW Model no Parts List for Figure C KEY Part NO. NumberDescription Qljan Figured KEY Part Number Parts List for Figure DFiguree Parts List for Figure E Figuref Parts List for Figure F Figureg Parts List for Figure G Figureh Parts List for Figure H Figurei Description Quan Parts List for FigureAu Canadapourserviceen franais

315.22839 specifications

The Craftsman 315.22839 is a versatile and reliable power tool that has gained popularity among DIY enthusiasts and professionals alike. Known for its robust construction and user-friendly features, this electric tool is perfect for a variety of tasks, from sanding and drilling to cutting.

One of the main features of the Craftsman 315.22839 is its powerful motor. Equipped with a reliable engine, it delivers impressive torque and speed, making it capable of tackling demanding projects. The tool boasts adjustable speed settings which allow users to customize the tool's performance based on the task at hand. This feature not only enhances precision but also promotes efficiency as users can switch speeds for different materials and applications.

Another standout attribute of the Craftsman 315.22839 is its ergonomic design. It has a comfortable grip that minimizes hand fatigue during extended use, ensuring that users can work longer and more efficiently. Additionally, the lightweight construction of the tool allows for easy maneuverability, making it ideal for both intricate and large-scale jobs.

The Craftsman 315.22839 also integrates advanced safety features. It includes a safety lock switch that prevents accidental startups, a crucial aspect for ensuring user safety during operation. The durable housing is designed to withstand the rigors of heavy usage, ensuring longevity and reliability in various work environments.

Versatility is a hallmark of the Craftsman brand, and the 315.22839 is no exception. It is compatible with a range of attachments and accessories, allowing users to switch between different functionalities. Whether you’re drilling into wood, cutting through metal, or sanding surfaces, the adaptable nature of this tool makes it a valuable addition to any toolbox.

In terms of technology, Craftsman has incorporated innovative engineering techniques to enhance the performance and durability of the 315.22839. Features like heat-resistant materials and advanced cooling systems ensure that the tool can operate under strenuous conditions without overheating or losing efficiency.

Overall, the Craftsman 315.22839 stands out in the crowded market of power tools. Its combination of power, efficiency, and user-friendly design makes it an excellent choice for both novice and experienced users looking for reliable performance. Whether you are embarking on a home improvement project or tackling a professional job, the 315.22839 is equipped to deliver results that meet your expectations.
Top Page Image Contents