Craftsman 315.22839 owner manual Mounting the LEG Stand on the Table SAW Base, Legstand Flatwasher

Page 19

ASSEMBLING LEG STAND (Continued)

•Align the two large holes on the brace and the legs. Insert the carriage bolts. Add fiat washers and hex nuts and hand tighten. Repeat for the other short upper brace. These are the front and back sets.

•For the sides, install a long upper brace on two legs. Add hardware and finger tighten. Repeat for the other long upper brace.

•Use the same steps to install the lower braces. Tighten all hex nuts with a 12 mm wrench.

•Place a hex nut and flat washer on each leveling foot. Install the leveling feet from the bottom of each leg with the bolts pointing up. Secure with a fiat washer and hex nut but do not tighten.

•Move the leg stand to desired location. Adjust the leveling feet with a 12 mm wrench, then securely tighten the top hex nut.

LEG 8TAND8HOWNA88EMBLED Fig. 8

MOUNTING THE LEG STAND ON THE TABLE

SAW BASE

See Figure 9.

•Take the following from the hardware bag:

4 hex bolts (5/16-18 x 3/4 in.)

4 hex nuts (5/16-18)

8 flat washers (5/16 in.)

Note: This hardware was in the bag with hardware for assembling the leg stand and leveling feet.

,_ WARNING: Do not lift the saw table without help. The table saw base weighs approximately

95 Ibs. Hold it close to your body. Keep your knees bent and lift with your legs, not your back. Ignoring these precautions can result in back injury.

•Place the leg stand on the table saw base. Align the holes in the table with the holes in the end

braces. Make sure the Craftsman label faces the front of the saw (same side as height handwheel).

•Place a flat washer on each bolt and insert through hole. Add a flat washer and a hex nut. Hand tighten.

•Repeat for the three remaining holes. Tighten all hardware with a 12 mm wrench. You may find it helpful to use two wrenches, one wrench to hold the head of the bolt and one to tighten the hex nut. Leave the saw upside down to add table exten- sions.

LEGSTAND

FLATWASHER

FLATWASHER

•Place the saw table upside down on a smooth surface, such as cardboard, on the floor.

Fig. 9

19rI_RFTSMRN°TABLESAW315.228390

Page 18 Page 20
Image 19
Page 18 Page 20
Contents IIRRFrSMRN Full ONE Year Warranty on Craftsman Table SAW 30-34 Safety Alert Symbol Symbol MeaningRules for Safe Operation Do not Feed the Material TOO Grounding Instructions Speed and WiringExtension Cords Electrical ConnectionRRRFTSMRH TABLESAW315.228390 Assembling parts, making adjustments, installing Assemble all parts to your saw before connectingIt to power supply. Saw should never be Connected to power supply when you areBelt Guard Blade Guard Assembly Hardware Screw#10-24x 1/2in Clip End cap for rear rail Cord Screw #8-32 x 1/2 Combinationsquare Hammer 45TRIANGLE NutdriverFramingsquare CRRFTSMRNTABLESAW315.22839014 Inch Table SawPush Offoi IorDo ExtensionNotLiftSawTablesWith. RailsBeltcover Levelingfoot Motor Bevel Lockhandle ScalehandleHeight Handwheel LEG StandOverview LEG Installing Handwheels on Table SAW BaseBevel Handwheel Height Upperbracewasher Hexnut Carriage BoltLegstand Flatwasher Mounting the LEG Stand on the Table SAW BaseSplit Rail Design Assemblingtable ExtensionsHEX Headbolt Flat Aligning Table ExtensionsSee Figures 12 Rearrail Connector EndcapHEX NUT SAW Tabletable Extension NUTHE BOLT8 Front RailRIP Fence Hook Over AssemblyAligning the RIP Fence and Front Rail See Figures 17Hexkeyframingsquare Throatplate SAW PulleyBelt Beltguard Checking the Throat PlateHEX InstallingBlade Blade Guard Bracket LockBlade J See Figures 26Rivingknife Blade Rivingknife Blade Throat Plate FramingMiter Gage Groove Framing SquareRIP Fence Framing AlignmentSee Figures 31 Miter Gage Groove BladeExtension Square Sawtable Checking Squareness of Extension Tables to SAW TableSquare SawtableBlade Blaiwasher Replacing the BladeSee Figures 35 Blade Guard To Loosen Blade NUTMitergagegroove BLADEGUARD18NOTSHOWNFORCLARITYAT Front NUT I Markedtooth Blade See Figures 38See Figures 41 Sawtableview Frombelow Rearsaw Table TablebracketHexkey 8TOP 8CREW Indicator Adjusting the Miter Gage8TOP 8CREW Adjustable Miterknob Gage ROD MiterSpringclip Removing Replacing the Throat ThroatplatePlate KEY 8LOTPUSHSTICK8 Avoiding KickbackTypes of Cuts Making a RIP CUT See Figures 47PLACELEFTHANDONWHENMITERGAGE18 Mitergagehereplacerighthandon MitergageknobhereBlade Mitergage Straight Angled Bevel Handwheel Height RIP CUTMaking a Miter CUT Miter CUTBevel Ripcut Bevelcrosscut BladeScale Blade Onworkpieceand Making a Compound Bevel Miter CUTPlacelefthandon Mitergagehere Mitergageknobhere NON-THROUGHCUT Pushstick Guard Blade Making a Large Panel CUTMaking a NON-THROUGH CUT Largepanelcut RIP FenceMaking a Dado CUT Dadocut Motor / Electrical General MaintenanceFrontof SAW Problem Cause Solution See Aligning Rip Fence See Heeling Sawblade AdjustmentsSetting Bevel Stops Indicator AdjustmentsFence. See Aligning Rip Fence Front Rail in the Assembly£RRFTSMRN Table SAW Figure a Description Parts List for Figure aKEY Part NO. NumberCraftsman Table SAW- Model no KEY Part NO. Number Parts List for Figure BCraftsman Table SAW Model no KEY Part NO. Number Parts List for Figure CDescription Qljan Figured KEY Part Number Parts List for Figure DFiguree Parts List for Figure E Figuref Parts List for Figure F Figureg Parts List for Figure G Figureh Parts List for Figure H Figurei Description Quan Parts List for FigureAu Canadapourserviceen franais

315.22839 specifications

The Craftsman 315.22839 is a versatile and reliable power tool that has gained popularity among DIY enthusiasts and professionals alike. Known for its robust construction and user-friendly features, this electric tool is perfect for a variety of tasks, from sanding and drilling to cutting.

One of the main features of the Craftsman 315.22839 is its powerful motor. Equipped with a reliable engine, it delivers impressive torque and speed, making it capable of tackling demanding projects. The tool boasts adjustable speed settings which allow users to customize the tool's performance based on the task at hand. This feature not only enhances precision but also promotes efficiency as users can switch speeds for different materials and applications.

Another standout attribute of the Craftsman 315.22839 is its ergonomic design. It has a comfortable grip that minimizes hand fatigue during extended use, ensuring that users can work longer and more efficiently. Additionally, the lightweight construction of the tool allows for easy maneuverability, making it ideal for both intricate and large-scale jobs.

The Craftsman 315.22839 also integrates advanced safety features. It includes a safety lock switch that prevents accidental startups, a crucial aspect for ensuring user safety during operation. The durable housing is designed to withstand the rigors of heavy usage, ensuring longevity and reliability in various work environments.

Versatility is a hallmark of the Craftsman brand, and the 315.22839 is no exception. It is compatible with a range of attachments and accessories, allowing users to switch between different functionalities. Whether you’re drilling into wood, cutting through metal, or sanding surfaces, the adaptable nature of this tool makes it a valuable addition to any toolbox.

In terms of technology, Craftsman has incorporated innovative engineering techniques to enhance the performance and durability of the 315.22839. Features like heat-resistant materials and advanced cooling systems ensure that the tool can operate under strenuous conditions without overheating or losing efficiency.

Overall, the Craftsman 315.22839 stands out in the crowded market of power tools. Its combination of power, efficiency, and user-friendly design makes it an excellent choice for both novice and experienced users looking for reliable performance. Whether you are embarking on a home improvement project or tackling a professional job, the 315.22839 is equipped to deliver results that meet your expectations.
Top Page Image Contents