Craftsman 315.22839 owner manual SAW Pulley, Belt Beltguard, Checking the Throat Plate, Headscrew

Page 24

INSTALLING THE BELT AND BELT GUARD See Figures 20 and 21.

•Get the belt, belt guard, 4 flat washers (#10) and 4 small hex nuts (#10-24).

•Lower the blade by turning the height handwheel.

•Slip the belt on the saw pulley (inside cabinet). Lift the motor forward and place the belt on the motor pulley.

•Check that the belt is straight and both pulleys are aligned. If not, adjust the motor on the motor support assembly. Refer to Mounting the Motor.

•Raise the saw blade all the way up.

•Pull the motor out until the belt is taut. Securely tighten the hex bolts above the rods with a 12 mm wrench.

•Put your hand around the belt halfway between the two pulleys and squeeze the belt until both sides of the belt touch. The motor should move freely as you squeeze the belt. If it does not, loosen the hex bolts and readjust the belt tension.

•Lower the blade with the height handwheel. Lift the motor forward and remove the belt.

•Open the hinged belt guard and place it over the motor screws on the motor pulley. Secure with flat

washers and hex nuts. Securely tighten the hex nuts with a 8 mm wrench.

•Replace the belt and snap the guard closed.

•Check the clearances by indexing the blade. Turn the bevel handwheel to 45 ° and back. Use the

height handwheel to fully lower and raise the blade.

SAW PULLEY

BELT

BELTGUARD

WASHER_ Fig. 21

CHECKING THE THROAT PLATE

See Figure 22.

,_ CAUTION: The throat plate must be even with the table surface. If it is too high or too low, the

workpiece can catch on uneven edges and cause kickback.

Make sure the throat plate is flush with the table top. To change height of the throat plate, loosen the flat head screw that secures the throat plate and adjust the four setscrews with a 2 mm hex key. Do

not allow the throat plate to bow up above the table surface.

2mmSETSCREW

HEXKEYFRAMINGSQUARE

THROATPLATE

HEADSCREW

TABLETOP

 

BELT

 

 

 

MOTOR

HEIGHT

 

 

PULLEY

 

 

HANDWHEEL

 

 

 

 

MOTORSCREW8

Fig. 20

BEVEL

Fig. 22

 

 

 

HANDWHEEL

 

 

 

CRRFTSMRN_TABLESAW315.228390

 

24

 

Page 23 Page 25
Image 24
Page 23 Page 25
Contents IIRRFrSMRN Full ONE Year Warranty on Craftsman Table SAW 30-34 Symbol Meaning Safety Alert SymbolRules for Safe Operation Do not Feed the Material TOO Speed and Wiring Extension CordsElectrical Connection Grounding InstructionsRRRFTSMRH TABLESAW315.228390 Assemble all parts to your saw before connecting It to power supply. Saw should never beConnected to power supply when you are Assembling parts, making adjustments, installingBelt Guard Blade Guard Assembly Hardware Screw#10-24x 1/2in Clip End cap for rear rail Cord Screw #8-32 x 1/2 Nutdriver Combinationsquare Hammer 45TRIANGLEFramingsquare Inch Table Saw CRRFTSMRNTABLESAW315.22839014IorDo ExtensionNotLiftSawTablesWith. Rails Push OffoiScalehandle Height HandwheelLEG Stand Beltcover Levelingfoot Motor Bevel LockhandleOverview Installing Handwheels on Table SAW Base Bevel Handwheel HeightUpperbracewasher Hexnut Carriage Bolt LEGMounting the LEG Stand on the Table SAW Base Legstand FlatwasherAssemblingtable Extensions HEX Headbolt FlatAligning Table Extensions Split Rail DesignRearrail Connector Endcap See Figures 12HEX NUT NUT HE BOLT8Front Rail SAW Tabletable ExtensionAssembly Aligning the RIP Fence and Front RailSee Figures 17 RIP Fence Hook OverSAW Pulley Belt BeltguardChecking the Throat Plate Hexkeyframingsquare ThroatplateInstalling BladeBlade Guard Bracket Lock HEXSee Figures 26 Rivingknife BladeRivingknife Blade Throat Plate Framing Blade JFraming Square Miter Gage GrooveAlignment See Figures 31Miter Gage Groove Blade RIP Fence FramingChecking Squareness of Extension Tables to SAW Table SquareSawtable Extension Square SawtableReplacing the Blade See Figures 35Blade Guard To Loosen Blade NUT Blade BlaiwasherBLADEGUARD18NOTSHOWNFORCLARITY AT Front NUT I Markedtooth BladeSee Figures 38 MitergagegrooveSawtableview Frombelow Rearsaw Table Tablebracket See Figures 41Hexkey Indicator Adjusting the Miter Gage 8TOP 8CREW AdjustableMiterknob Gage ROD Miter 8TOP 8CREWRemoving Replacing the Throat Throatplate PlateKEY 8LOT SpringclipAvoiding Kickback PUSHSTICK8Types of Cuts See Figures 47 PLACELEFTHANDONWHENMITERGAGE18Mitergagehereplacerighthandon Mitergageknobhere Making a RIP CUTRIP CUT Making a Miter CUTMiter CUT Blade Mitergage Straight Angled Bevel Handwheel HeightBevelcrosscut Blade Bevel RipcutScale Blade Making a Compound Bevel Miter CUT OnworkpieceandPlacelefthandon Mitergagehere Mitergageknobhere Making a Large Panel CUT Making a NON-THROUGH CUTLargepanelcut RIP Fence NON-THROUGHCUT Pushstick Guard BladeMaking a Dado CUT Dadocut General Maintenance Motor / ElectricalFrontof SAW Problem Cause Solution See Heeling Sawblade Adjustments Setting Bevel StopsIndicator Adjustments See Aligning Rip FenceFront Rail in the Assembly Fence. See Aligning Rip Fence£RRFTSMRN Table SAW Figure a Parts List for Figure a KEY PartNO. Number DescriptionCraftsman Table SAW- Model no Parts List for Figure B KEY Part NO. NumberCraftsman Table SAW Model no Parts List for Figure C KEY Part NO. NumberDescription Qljan Figured Parts List for Figure D KEY Part NumberFiguree Parts List for Figure E Figuref Parts List for Figure F Figureg Parts List for Figure G Figureh Parts List for Figure H Figurei Parts List for Figure Description QuanAu Canadapourserviceen franais

315.22839 specifications

The Craftsman 315.22839 is a versatile and reliable power tool that has gained popularity among DIY enthusiasts and professionals alike. Known for its robust construction and user-friendly features, this electric tool is perfect for a variety of tasks, from sanding and drilling to cutting.

One of the main features of the Craftsman 315.22839 is its powerful motor. Equipped with a reliable engine, it delivers impressive torque and speed, making it capable of tackling demanding projects. The tool boasts adjustable speed settings which allow users to customize the tool's performance based on the task at hand. This feature not only enhances precision but also promotes efficiency as users can switch speeds for different materials and applications.

Another standout attribute of the Craftsman 315.22839 is its ergonomic design. It has a comfortable grip that minimizes hand fatigue during extended use, ensuring that users can work longer and more efficiently. Additionally, the lightweight construction of the tool allows for easy maneuverability, making it ideal for both intricate and large-scale jobs.

The Craftsman 315.22839 also integrates advanced safety features. It includes a safety lock switch that prevents accidental startups, a crucial aspect for ensuring user safety during operation. The durable housing is designed to withstand the rigors of heavy usage, ensuring longevity and reliability in various work environments.

Versatility is a hallmark of the Craftsman brand, and the 315.22839 is no exception. It is compatible with a range of attachments and accessories, allowing users to switch between different functionalities. Whether you’re drilling into wood, cutting through metal, or sanding surfaces, the adaptable nature of this tool makes it a valuable addition to any toolbox.

In terms of technology, Craftsman has incorporated innovative engineering techniques to enhance the performance and durability of the 315.22839. Features like heat-resistant materials and advanced cooling systems ensure that the tool can operate under strenuous conditions without overheating or losing efficiency.

Overall, the Craftsman 315.22839 stands out in the crowded market of power tools. Its combination of power, efficiency, and user-friendly design makes it an excellent choice for both novice and experienced users looking for reliable performance. Whether you are embarking on a home improvement project or tackling a professional job, the 315.22839 is equipped to deliver results that meet your expectations.
Top Page Image Contents