Panasonic SC-BT203, SC-BT200, SC-BT303 warranty Listening to the Radio, Setting up the radio

Listening to the Radio

Setting up the radio

	1@.	2ABC	3DEF
Numbered	4GHI	5JKL	6MNO
buttons	P	8TUV	W
	7QRS		9XYZ
		0_,

	RADIO	RADIO
	EXT-IN
SEARCH	SEARCH	SEARCH
		SEARCH
		,

Listening/confirming the preset channels

1Press [RADIO] to select “FM” or “AM”.

2 Press the numbered buttons to select the channel.

To select a 1-digit number e.g., 1: [1] > [OK].

To select a 2-digit number e.g., 12: [1] B [2]

Alternatively, press [W, X] or [2, 1].

When a stereo FM broadcast is being received,
	ST
“ST” lights in the display.

≥The FM/AM setting is also shown on the TV display.

Radio

OK

OK

STATUS AUDIO

STATUS AUDIO

SD CARD SETUP MIC SELECTOR TUNE

∫If noise is excessive

When FM is selected

Press [AUDIO] to display “MONO”. T MONO

Press the button again to cancel the mode.

≥The mode is also canceled when you change the frequency. ≥This setting can be preset for each broadcasting station. When

“MONO” appears, follow procedures 1 and 2 in “Presetting stations manually”. (> below)

When AM is selected

Press [AUDIO] to select “AM BP1” or “AM BP2” (whichever receives the better quality).

Each time you press the button:

AM BP1(.AM BP2 (BP=Beat Proof)

Manual tuning

SELECTOR TUNE	1 Press [RADIO] to select “FM” or “AM”.
Presetting stations automatically	2 Press [SEARCH6] or [SEARCH5] to select
Up to 30 stations can be set in each band, FM and AM.	the frequency.
1 Press [RADIO] to select “FM” or “AM”.	≥Main unit:
2 Press [STATUS] to select the position to start the	Press [X TUNE W] to select the frequency.
	≥When a radio broadcast is being
		T	MONO
auto preset search.	received, “T” lights in the display.
Each time you press the button:	≥To start automatic tuning, press
LOWEST (factory preset):	and hold [SEARCH6] or
To begin auto preset with the lowest frequency.	[SEARCH5] (main unit: [X TUNE W]) until the frequency
(FM: 87.9 or 87.5, AM: 520)	starts scrolling.
CURRENT:	Tuning stops when a station is found.
To begin auto preset with the current frequency.*	∫ Presetting stations manually
* To change the frequency, refer to “Manual tuning”. (B right)	Up to 30 stations can be set in each band, FM and AM.
3 Press and hold [OK].	1 While listening to the radio broadcast
	Press [OK].
Release the button when “AUTO” is
	2 While “P” is flashing on the display
displayed.
	Press the numbered buttons to select a channel.
The tuner starts to preset all the stations it
	To select a 1-digit number
can receive into the channels in ascending
	e.g., 1: [1] > [OK].
order.
	To select a 2-digit number
≥“SET OK” is displayed when the stations are set, and the radio tunes	e.g., 12: [1] B [2]
to the last preset station.	A station previously stored is overwritten when another station is
≥“ERROR” is displayed when automatic presetting is unsuccessful.	stored in the same channel preset.
Preset the stations manually. (B right)

FM frequency step

Main unit:

The factory setting is set to 0.2 MHz, it can be changed to receive broadcasts allocated in 0.1 MHz. You may need to change this setting if the tuner seems to skip over the correct frequency for stations in your area.

1Press [SELECTOR] to select “FM”.

2 Press and hold [SELECTOR].

After a few seconds the display changes to show the current lowest frequency. Continue to hold the button down. The lowest frequency changes and the step is changed.

To return to the original settings, repeat steps 1 and 2.

After changing the setting, previously preset frequencies will be cleared. Preset them again.

RQT9508 NOTE

26