Intel SBX82 Electromagnetic compatibility notices International, Japan EMC Compatibility, Xiii

Page 13

Electromagnetic compatibility notices (International)

Europe (CE Declaration of Conformity): This product has been tested in accordance too, and complies with the Low Voltage Directive (73/23/EEC) and EMC Directive (89/336/EEC). The product has been marked with the CE Mark to illustrate its compliance.

Japan EMC Compatibility:

English translation of the notice above: This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions.

ICES-003 (Canada): Cet appareil numérique respecte les limites bruits radioélectriques applicables aux appareils numériques de Classe A prescrites dans la norme sur le matériel brouilleur: "Appareils Numériques", NMB-003 édictée par le Ministre Canadian des Communications.

English translation of the notice above: This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the interference-causing equipment standard entitled "Digital Apparatus," ICES-003 of the Canadian Department of Communications.

BSMI (Taiwan): The BSMI Certification number and the following warning is located on the product safety label which is located visibly on the external chassis.

xiii

Image 13
Contents Intel Server Compute Blade SBX82 Disclaimer Contents Configuring the blade server Safety and regulatory information Electrical Safety General SafetyVii Handling electrostatic discharge-sensitive devices To Connect To Disconnect Use safe practices when lifting Safety compliance Regulatory specifications and disclaimersElectromagnetic compatibility ECM Electromagnetic compatibility notices USAJapan EMC Compatibility Electromagnetic compatibility notices InternationalXiii Device User’s Information RRL Korea English translation of the notice abovePage Blade server release levers Label placement on the Sbce unit Reliability, availability, and serviceability features Features and specificationsIntel Server Compute Blade SBX82 features Power throttling Intel Server Compute Blade SBX82 specificationsProcessor Size Electrical Input Service ProcessorEnvironment Memory Integrated functionsRelated publications Major components of the blade serverPage Page Turning on the blade server Using power, controls, jumpers, switches, and indicatorsTurning off the blade server Understanding the control panel and LEDs NumLock NumLock bladeservernumber Enter System board illustration Using system board switchesSwitch block 2 SW2 and settings Using switch block 2 SW2NMI MIS Sbrd Temp MIS System reliability considerations Installation guidelinesHandling static-sensitive devices Opening the blade server cover Installing and removing the blade server from the Sbce unitStatement Removing the blade server bezel assemblyInstalling a Scsi drive Installing a Scsi hard disk driveRemoving a Scsi hard disk drive Installing memory modulesInstalling Dimms Installing an additional processor Page Lever fully open Lever closed Installing an I/O expansion card Installing a small form-factor expansion card Installing a small form-factor I/O card in the blade server Installing a standard form-factor expansion card Sbescsi IInstalling the Intel Blade Server Scsi Expansion ModuleInstalling a Scsi storage expansion unit Cover pins Scsi IDs for the hard disk drives in the expansion unit Installing a Scsi disk drive Page Opening the expansion unit cover Installing an I/O expansion card Installing an I/O expansion card in the expansion unit Replacing the battery Battery location Completing the installation Installing the blade server bezel assembly Closing the blade server cover Installing the blade server in the Sbce unit Updating your blade server configuration Input/output connectors and devices Starting the Configuration/Setup Utility program Using the Configuration/Setup Utility programConfiguration/Setup Utility menu choices Product Data System InformationDevices and I/O Ports Remote Console RedirectionMemory Settings Advanced SetupBaseboard Management Controller BMC Settings BMC Network ConfigurationUsing passwords Firmware updates Using the PXE boot agent utility programConfiguring the Gigabit Ethernet controllers Blade server Ethernet controller enumeration Configuring a Scsi RAID arrayUsing the LSI Logic Configuration Utility program Troubleshooting charts Diagnostic tools overviewDiagnostic programs and error messages Light Path Diagnostics featureRepeating long beeps Post beep code descriptionsAbbreviated list of Post error messages Post error messagesAbbreviated list of Post error messages Memory problems Troubleshooting chartsProcessor problems Mm 3 Monitor problemsNetwork connection problems Mouse problemsPower problems Option problemsService processor problems Light path diagnosticsDiagnosing problems using Light Path Diagnostics Light Path Diagnostics LEDsLight Path Diagnostics table Light path diagnostics Page Before you call Using the documentationGetting help and information from the World Wide Web Page Index Password Scsi RAID