Intel SBX82 manual Opening the expansion unit cover, Statement

Page 52

Opening the expansion unit cover

The following illustration shows how to open the expansion unit cover.

Cover release (both sides)

Complete the following steps to open the expansion unit cover:

1.Read the safety information beginning on page “Installation guidelines” on page 19.

2.Carefully lay the expansion unit down on a flat, non-conductive surface, with the cover side up.

3.Press the unit-cover release on each side of the expansion unit and lift the cover open, as shown in the illustration.

4.Lay the cover flat, or lift it from the expansion unit and store for future use.

Statement 21:

xxCAUTION:

Hazardous energy is present when the blade server is connected to the power source. Always replace the blade cover before installing the blade server.

38

Intel Server Compute Blade SBX82 Installation and User’s Guide

Image 52
Contents Intel Server Compute Blade SBX82 Disclaimer Contents Configuring the blade server Safety and regulatory information General Safety Electrical SafetyVii Handling electrostatic discharge-sensitive devices To Connect To Disconnect Use safe practices when lifting Regulatory specifications and disclaimers Safety complianceElectromagnetic compatibility notices USA Electromagnetic compatibility ECMJapan EMC Compatibility Electromagnetic compatibility notices InternationalXiii RRL Korea English translation of the notice above Device User’s InformationPage Blade server release levers Label placement on the Sbce unit Features and specifications Reliability, availability, and serviceability featuresIntel Server Compute Blade SBX82 features Intel Server Compute Blade SBX82 specifications Power throttlingService Processor Processor Size Electrical InputEnvironment Memory Integrated functionsMajor components of the blade server Related publicationsPage Page Using power, controls, jumpers, switches, and indicators Turning on the blade serverTurning off the blade server Understanding the control panel and LEDs NumLock NumLock bladeservernumber Enter Using system board switches System board illustrationUsing switch block 2 SW2 Switch block 2 SW2 and settingsNMI MIS Sbrd Temp MIS System reliability considerations Installation guidelinesHandling static-sensitive devices Installing and removing the blade server from the Sbce unit Opening the blade server coverRemoving the blade server bezel assembly StatementInstalling a Scsi hard disk drive Installing a Scsi driveInstalling memory modules Removing a Scsi hard disk driveInstalling Dimms Installing an additional processor Page Lever fully open Lever closed Installing an I/O expansion card Installing a small form-factor expansion card Installing a small form-factor I/O card in the blade server Installing a standard form-factor expansion card IInstalling the Intel Blade Server Scsi Expansion Module SbescsiInstalling a Scsi storage expansion unit Cover pins Scsi IDs for the hard disk drives in the expansion unit Installing a Scsi disk drive Page Opening the expansion unit cover Installing an I/O expansion card Installing an I/O expansion card in the expansion unit Replacing the battery Battery location Completing the installation Installing the blade server bezel assembly Closing the blade server cover Installing the blade server in the Sbce unit Updating your blade server configuration Input/output connectors and devices Starting the Configuration/Setup Utility program Using the Configuration/Setup Utility programConfiguration/Setup Utility menu choices System Information Product DataDevices and I/O Ports Remote Console RedirectionAdvanced Setup Memory SettingsBaseboard Management Controller BMC Settings BMC Network ConfigurationUsing passwords Using the PXE boot agent utility program Firmware updatesConfiguring the Gigabit Ethernet controllers Configuring a Scsi RAID array Blade server Ethernet controller enumerationUsing the LSI Logic Configuration Utility program Diagnostic tools overview Troubleshooting chartsDiagnostic programs and error messages Light Path Diagnostics featurePost beep code descriptions Repeating long beepsPost error messages Abbreviated list of Post error messagesAbbreviated list of Post error messages Memory problems Troubleshooting chartsProcessor problems Monitor problems Mm 3Mouse problems Network connection problemsOption problems Power problemsLight path diagnostics Service processor problemsDiagnosing problems using Light Path Diagnostics Light Path Diagnostics LEDsLight Path Diagnostics table Light path diagnostics Page Before you call Using the documentationGetting help and information from the World Wide Web Page Index Password Scsi RAID