Intel SBX82 manual Installing and removing the blade server from the Sbce unit

Page 34

Do not leave the device where others can handle and possibly damage it.

While the device is still in its non-conductive package, touch it to an unpainted metal part of the SBCE unit or any unpainted metal surface on any other grounded rack component in the rack you are installing the device in for at least 2 seconds. This drains static electricity from the package and from your body.

Remove the device from its package and install it directly into the blade server without setting it down. If it is necessary to set the device down, place it back into its non-conductive package. Do not place the device on your blade server cover or on a metal surface.

Take additional care when handling devices during cold weather. Heating reduces indoor humidity and increases static electricity.

Installing and removing the blade server from the SBCE unit

To install or remove a blade server from the SBCE unit, see the documentation that came with your unit for instructions.

Opening the blade server cover

The following illustration shows how to open the cover on the blade server.

Blade-cover release

Blade-cover release

20

Intel Server Compute Blade SBX82 Installation and User’s Guide

Image 34
Contents Intel Server Compute Blade SBX82 Disclaimer Contents Configuring the blade server Safety and regulatory information General Safety Electrical SafetyVii Handling electrostatic discharge-sensitive devices To Connect To Disconnect Use safe practices when lifting Regulatory specifications and disclaimers Safety complianceElectromagnetic compatibility notices USA Electromagnetic compatibility ECMJapan EMC Compatibility Electromagnetic compatibility notices InternationalXiii RRL Korea English translation of the notice above Device User’s InformationPage Blade server release levers Label placement on the Sbce unit Features and specifications Reliability, availability, and serviceability featuresIntel Server Compute Blade SBX82 features Intel Server Compute Blade SBX82 specifications Power throttlingEnvironment Service ProcessorProcessor Size Electrical Input Memory Integrated functionsMajor components of the blade server Related publicationsPage Page Using power, controls, jumpers, switches, and indicators Turning on the blade serverTurning off the blade server Understanding the control panel and LEDs NumLock NumLock bladeservernumber Enter Using system board switches System board illustrationUsing switch block 2 SW2 Switch block 2 SW2 and settingsNMI MIS Sbrd Temp MIS System reliability considerations Installation guidelinesHandling static-sensitive devices Installing and removing the blade server from the Sbce unit Opening the blade server coverRemoving the blade server bezel assembly StatementInstalling a Scsi hard disk drive Installing a Scsi driveInstalling memory modules Removing a Scsi hard disk driveInstalling Dimms Installing an additional processor Page Lever fully open Lever closed Installing an I/O expansion card Installing a small form-factor expansion card Installing a small form-factor I/O card in the blade server Installing a standard form-factor expansion card IInstalling the Intel Blade Server Scsi Expansion Module SbescsiInstalling a Scsi storage expansion unit Cover pins Scsi IDs for the hard disk drives in the expansion unit Installing a Scsi disk drive Page Opening the expansion unit cover Installing an I/O expansion card Installing an I/O expansion card in the expansion unit Replacing the battery Battery location Completing the installation Installing the blade server bezel assembly Closing the blade server cover Installing the blade server in the Sbce unit Updating your blade server configuration Input/output connectors and devices Starting the Configuration/Setup Utility program Using the Configuration/Setup Utility programConfiguration/Setup Utility menu choices Devices and I/O Ports System InformationProduct Data Remote Console RedirectionBaseboard Management Controller BMC Settings Advanced SetupMemory Settings BMC Network ConfigurationUsing passwords Using the PXE boot agent utility program Firmware updatesConfiguring the Gigabit Ethernet controllers Configuring a Scsi RAID array Blade server Ethernet controller enumerationUsing the LSI Logic Configuration Utility program Diagnostic programs and error messages Diagnostic tools overviewTroubleshooting charts Light Path Diagnostics featurePost beep code descriptions Repeating long beepsPost error messages Abbreviated list of Post error messagesAbbreviated list of Post error messages Memory problems Troubleshooting chartsProcessor problems Monitor problems Mm 3Mouse problems Network connection problemsOption problems Power problemsDiagnosing problems using Light Path Diagnostics Light path diagnosticsService processor problems Light Path Diagnostics LEDsLight Path Diagnostics table Light path diagnostics Page Before you call Using the documentationGetting help and information from the World Wide Web Page Index Password Scsi RAID