Intel SBX82 manual Removing a Scsi hard disk drive, Installing memory modules

Page 37

6.Place the drive into the tray and push it, from the rear edge of the drive, into the connector until the drive moves past the lever at the back of the tray. The drive clicks into place.

7.If you have other options to install or remove, do so now; otherwise, go to “Completing the installation” on page 43.

Removing a SCSI hard disk drive

To remove the SCSI hard disk drive, complete the following steps:

1.Read the safety information beginning on page “Safety” on page vii and “Installation guidelines” on page 19.

2.Shut down the operating system, turn off the blade server, and remove the blade server from the SBCE unit (see “Installing and removing the blade server from the SBCE unit” on page 20 for instructions).

3.Carefully lay the blade server on a flat, non-conductive surface.

4.Open the blade server cover (see “Opening the blade server cover” on page 20 for instructions).

5.Locate SCSI connector 1 and slowly pull the blue lever at the back of the hard disk drive tray to disengage the drive from its tray.

6.From the rear edge of the drive, slide the drive out of the SCSI connector.

Attention: To maintain proper system cooling, do not operate the system unit without either a blade server, expansion unit, or filler blade installed in each blade bay for more than 1 minute.

Installing memory modules

The following notes describe the types of dual inline memory modules (DIMMs) that the blade server supports and other information that you must consider when installing DIMMs:

•The system board contains four DIMM connectors and supports two-way memory interleaving.

•The DIMM options that are available for your blade server are 256 MB, 512 MB, 1 GB, and

2 GB. Your blade server supports a minimum of 256 MB and a maximum of 8 GB of system memory.

•Your blade server comes with two DIMMs in the DIMM 1 (J113) and DIMM 2 (J111) memory connectors.

When you install additional DIMMs, be sure to install them as a pair, in DIMM connectors 3 (J112) and 4 (J110).

Install the DIMMs in the following order:

Pair	DIMM connectors
First	1 (J113) and 2 (J111)
Second	3 (J112) and 4 (J110)

23

Image 37

Contents Intel Server Compute Blade SBX82 Disclaimer Contents Configuring the blade server Safety and regulatory information Electrical Safety General SafetyVii Handling electrostatic discharge-sensitive devices To Connect To Disconnect Use safe practices when lifting Safety compliance Regulatory specifications and disclaimersElectromagnetic compatibility ECM Electromagnetic compatibility notices USAJapan EMC Compatibility Electromagnetic compatibility notices InternationalXiii Device User’s Information RRL Korea English translation of the notice abovePage Blade server release levers Label placement on the Sbce unit Reliability, availability, and serviceability features Features and specificationsIntel Server Compute Blade SBX82 features Power throttling Intel Server Compute Blade SBX82 specificationsProcessor Size Electrical Input Service ProcessorEnvironment Memory Integrated functionsRelated publications Major components of the blade serverPage Page Turning on the blade server Using power, controls, jumpers, switches, and indicatorsTurning off the blade server Understanding the control panel and LEDs NumLock NumLock bladeservernumber Enter System board illustration Using system board switchesSwitch block 2 SW2 and settings Using switch block 2 SW2NMI MIS Sbrd Temp MIS System reliability considerations Installation guidelinesHandling static-sensitive devices Opening the blade server cover Installing and removing the blade server from the Sbce unitStatement Removing the blade server bezel assemblyInstalling a Scsi drive Installing a Scsi hard disk driveRemoving a Scsi hard disk drive Installing memory modulesInstalling Dimms Installing an additional processor Page Lever fully open Lever closed Installing an I/O expansion card Installing a small form-factor expansion card Installing a small form-factor I/O card in the blade server Installing a standard form-factor expansion card Sbescsi IInstalling the Intel Blade Server Scsi Expansion ModuleInstalling a Scsi storage expansion unit Cover pins Scsi IDs for the hard disk drives in the expansion unit Installing a Scsi disk drive Page Opening the expansion unit cover Installing an I/O expansion card Installing an I/O expansion card in the expansion unit Replacing the battery Battery location Completing the installation Installing the blade server bezel assembly Closing the blade server cover Installing the blade server in the Sbce unit Updating your blade server configuration Input/output connectors and devices Starting the Configuration/Setup Utility program Using the Configuration/Setup Utility programConfiguration/Setup Utility menu choices Product Data System InformationDevices and I/O Ports Remote Console RedirectionMemory Settings Advanced SetupBaseboard Management Controller BMC Settings BMC Network ConfigurationUsing passwords Firmware updates Using the PXE boot agent utility programConfiguring the Gigabit Ethernet controllers Blade server Ethernet controller enumeration Configuring a Scsi RAID arrayUsing the LSI Logic Configuration Utility program Troubleshooting charts Diagnostic tools overviewDiagnostic programs and error messages Light Path Diagnostics featureRepeating long beeps Post beep code descriptionsAbbreviated list of Post error messages Post error messagesAbbreviated list of Post error messages Memory problems Troubleshooting chartsProcessor problems Mm 3 Monitor problemsNetwork connection problems Mouse problemsPower problems Option problemsService processor problems Light path diagnosticsDiagnosing problems using Light Path Diagnostics Light Path Diagnostics LEDsLight Path Diagnostics table Light path diagnostics Page Before you call Using the documentationGetting help and information from the World Wide Web Page Index Password Scsi RAID