Graco ti13585a, ti13586a Installation, Ventilate Spray Booth, Configure Gun and Manifold

Page 10

Installation

Installation

The Automatic AirPro spray gun can spray most coatings or finishes currently being used for automotive, industrial, aerospace, marine, wood, plastic and architectural applications, while easily operating from paint delivery sys- tems, such as pressure pots or remote pumps for production line operation.

The air regulator must have a minimum air flow capacity of 30 scfm at 100 psi (0.7 MPa, 7.0 bar) air pressure.

Ventilate Spray Booth

•Check and follow all national, state, and local codes regarding air exhaust velocity requirements.

•Check and follow all local safety and fire codes.

Configure Gun and Manifold

The gun is supplied with an internal fluid plug and seals (19, 20, 21). To use the gun in a cir- culating system, remove the internal plug. In a non-circulating system, leave the plug in place to minimize flush time.

Circulating System

1.Apply anti-seize lubricant to the threads and mating faces of the manifold (101) and the elbows (107), supplied unassembled.

2.Install the elbows (107) in both fluid ports of the manifold (101).

3.Connect the fluid supply line to one elbow and the fluid return line to the other. The manifold fluid ports are reversible.

4.Install the gun on the manifold, using the four screws (13). Start the threads of all four screws. Tighten the front two screws first, and then tighten the back two. Torque all four screws evenly to 65 in-lb (7.3 N•m).

Non-circulating System

1.See FIG. 1. Apply anti-seize lubricant to the threads and mating faces of the manifold (101), plug (109), and elbow (107), sup- plied unassembled.

2.Install an elbow (107) in one fluid port of the manifold (101), and a plug (109) in the other port.

3.Install the internal plug (19) in the gun fluid port on the same side as the manifold plug.

4.Connect the fluid supply line to the fluid inlet elbow (107).

5.Install the gun on the manifold, using the four screws supplied. Start the threads of all four screws. Tighten the front two screws first, and then tighten the back two. Torque all four screws evenly to 65 in-lb (7.3 N•m).

1 Remove when used in circulating systems.

2Replace with elbow (107) when used in circulating systems.

21

20

101

1 19

107

2 109

ti8587b

FIG. 1: Non-Circulating Setup Shown (cutaway view)

10

313516G

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Important Safety Instructions Automatic AirPro Spray GunsContents ModelsFire and Explosion Hazard Pressurized Equipment Hazard Selection Charts General Metal ApplicationsGun Selection High Wear ApplicationsWood Applications Hvlp GunsAir Caps Proper Needle/Nozzle SelectionConventional Guns Air Flow Atomizing Air Fan AirMaximum HVLP/Compliant inlet manifold pressure Configure Gun and Manifold InstallationVentilate Spray Booth Circulating SystemInstall Air Fittings Ground SystemReciprocating Arm Rod Mount Mount GunStationary Support Retrofit Adapter Plate Retrofit Adapter Plate MountConnect Air Line SetupConnect Fluid Hose Flush Spray Gun Position Air CapSuggested Starting Settings Atomization Adjust Spray PatternFan Air psi Air Pressure Regulator Apply Fluid Pressure Relief ProcedureOperation IncorrectDaily Gun Care General System Maintenance Clean and Flush GunGeneral Troubleshooting TroubleshootingProblem Cause Solution Spray Pattern Troubleshooting Service DisassemblyPart No A749 Gun Shown Reassembly Fluid packingsParts Gasket Repair Kits General Metal ApplicationsHigh Wear Applications Wood Applications114101 103 107 105108 Side Fluid Ports and Fan Adjustment Valve Part No C342107 101 114 103 106 Accessories Spray Tip Filters Hvlp Pressure Verification KitInline Fluid Filter 24B707 TipsManifold Models 288217 or 288218, All Gun Models DimensionsManifold Model 288221, All Gun Models Manifold Model 288223 or 24C342, All Gun Models Manifold Model 288160 or 288211, All Gun ModelsMounting Hole Layouts 23.4 mm 10.2 mm 53.3 mm 50 in .7 mm mounting hole 216 225 58.4 mm Retrofit Adapter Plate Triggering Speed Technical DataSound Data Graco Standard Warranty Graco Information

ti13586a, ti13585a specifications

The Graco TI13586A and TI13585A are advanced airless paint sprayers designed for both professional contractors and serious DIY enthusiasts. These models stand out for their ability to deliver high-quality finishes quickly and efficiently, making them ideal for a wide range of painting tasks, from residential projects to large-scale commercial applications.

One of the main features of the Graco TI13586A and TI13585A is their powerful motor. These sprayers come equipped with a robust 0.75 HP pump that can generate high pressure, allowing for thorough and consistent coverage on various surfaces. This motor works efficiently to atomize the paint, producing a fine spray pattern essential for achieving a smooth finish without the need for excessive back-and-forth motion.

Another notable characteristic is the ease of use. The Graco TI13586A and TI13585A include an easy-to-operate control system that allows users to adjust the pressure settings, ensuring optimal spray control for various painting materials and techniques. This versatility is complemented by the FlexLiner container system, which reduces waste and allows for easy cleaning between jobs.

In terms of portability, these models are designed with mobility in mind. The lightweight construction, along with a durable cart that features large wheels, makes it easy to transport the sprayers to different job sites. Whether you're navigating stairs or uneven terrain, the design ensures that transportation remains hassle-free.

Both models are compatible with a variety of coatings, including latex paints, stains, and sealers, enhancing their adaptability for numerous applications. They also leverage Graco's proven Airless Technology, which ensures a consistent finish by using a piston pump system that allows for continuous operation without the risk of clogging. This technology results in faster project completion times, which is a significant advantage for contractors on a tight schedule.

Additionally, safety features such as a settings lock and the built-in pressure relief valve contribute to user protection while enhancing the overall painting experience. This focus on safety and efficiency ensures that both the TI13586A and TI13585A maintain Graco's reputation for quality and reliability in the airless spraying market.

In summary, both the Graco TI13586A and TI13585A represent powerful, user-friendly solutions for quality airless painting. Their effective motor, adjustable pressure settings, portability, and compatibility with various materials make them excellent choices for anyone looking to achieve professional-level results with ease and efficiency.
Top Page Image Contents