Graco ti13586a, ti13585a important safety instructions Reassembly, Fluid packings

Page 25

Reassembly

1.Non-circulating guns only: Lubricate the backup ring (20†) and o-ring (21†) and install them on the fluid outlet port plug

(19). Install the plug in the fluid outlet port of the fluid housing (2). See FIG. 21.

2.All guns: Reinstall the gasket (22) in the fluid housing (2).

3.Install the o-rings (8*, 9*) on the piston (3). Install the two o-rings (10*, 11*) on each of the piston stems (T). Lubricate all the o-rings, the piston, and the piston stems.

4.Remove the protective paper from the sticky side of the gasket (12*) and adhere the gasket to the bottom of the piston hous- ing (1), making sure the three holes in the gasket are properly aligned with the match- ing holes in the housing.

5.Lubricate the washers (45†) and spacer (46†). Insert them into the packing nut (16) as shown in FIG. 20, The step on the spacer faces into the packing nut.

Service

Torque the two screws (14) to 35-45 in-lb (4.0-5.1 N•m).

a.Insert the piston (3) into the piston housing (1).

b.Ensure nozzle sealing o-ring (36) is installed on nozzle (23).

8.To avoid galling of the fluid nozzle seat in the fluid housing, apply a thin film of lubri- cant to the threads. Install the nozzle into the fluid housing. Torque the nozzle securely to 35-45 in-lb (4.0-5.1 N•m).

NOTE: If you are replacing the needle tip (5a), apply semi-permanent anaerobic sealant to two threads at the end of the needle shaft. Assemble the needle tip to the shaft and hand tighten. Allow adequate time for the sealant to cure before installing the needle assembly into the gun.

9. Lubricate and install the needle (5) into the

back of the gun assembly. Push it straight

in through the piston.

10. Install the needle stop (29) on the needle.

45

16

46 45

ti17603a

Coat the setscrew (30) with semi-perma-

nent anaerobic sealant and install the

screw into the needle stop. Torque to

6.5-7.5 in-lb (0.73-0.85 N•m). Pull on the

needle to make sure it seats fully.

11. Install the springs (6, 7).

12. Lubricate the threads of the piston housing

(1). Screw the cap (4) onto the housing

FIG. 20. Fluid packings

6.Insert the packing nut into the fluid housing

(2) and torque to 95-105 in-lb (10.7-11.8 N•m).

7.Align the gasket (15*) as shown in the exploded view in FIG. 21. Place the gasket on the piston housing (1), then install the fluid housing (2) onto the piston housing.

until it bottoms out.

13. Install the air cap (24) and air cap retainer

(25).

14. Reinstall the gun on the manifold using the

four screws (13). Start the threads of all

four screws. Tighten the front two screws

first, and then tighten the back two. Torque

all four screws evenly to 65 in-lb (7.3 N•m).

313516G

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Automatic AirPro Spray Guns Important Safety InstructionsModels ContentsFire and Explosion Hazard Pressurized Equipment Hazard General Metal Applications Selection ChartsWood Applications High Wear ApplicationsGun Selection Hvlp GunsAir Caps Proper Needle/Nozzle SelectionConventional Guns Atomizing Air Fan Air Air FlowMaximum HVLP/Compliant inlet manifold pressure Ventilate Spray Booth InstallationConfigure Gun and Manifold Circulating SystemGround System Install Air FittingsReciprocating Arm Rod Mount Mount GunStationary Support Retrofit Adapter Plate Mount Retrofit Adapter PlateConnect Air Line SetupConnect Fluid Hose Position Air Cap Flush Spray GunSuggested Starting Settings Atomization Adjust Spray PatternFan Air psi Air Pressure Regulator Operation Pressure Relief ProcedureApply Fluid IncorrectDaily Gun Care Clean and Flush Gun General System MaintenanceGeneral Troubleshooting TroubleshootingProblem Cause Solution Spray Pattern Troubleshooting Disassembly ServicePart No A749 Gun Shown Fluid packings ReassemblyParts Gasket General Metal Applications Repair KitsWood Applications High Wear Applications114101 103 107 105108 Part No C342 Side Fluid Ports and Fan Adjustment Valve107 101 114 103 106 Accessories Inline Fluid Filter 24B707 Hvlp Pressure Verification KitSpray Tip Filters TipsManifold Models 288217 or 288218, All Gun Models DimensionsManifold Model 288221, All Gun Models Manifold Model 288160 or 288211, All Gun Models Manifold Model 288223 or 24C342, All Gun ModelsMounting Hole Layouts 23.4 mm 10.2 mm 53.3 mm 50 in .7 mm mounting hole 216 225 58.4 mm Retrofit Adapter Plate Triggering Speed Technical DataSound Data Graco Information Graco Standard Warranty

ti13586a, ti13585a specifications

The Graco TI13586A and TI13585A are advanced airless paint sprayers designed for both professional contractors and serious DIY enthusiasts. These models stand out for their ability to deliver high-quality finishes quickly and efficiently, making them ideal for a wide range of painting tasks, from residential projects to large-scale commercial applications.

One of the main features of the Graco TI13586A and TI13585A is their powerful motor. These sprayers come equipped with a robust 0.75 HP pump that can generate high pressure, allowing for thorough and consistent coverage on various surfaces. This motor works efficiently to atomize the paint, producing a fine spray pattern essential for achieving a smooth finish without the need for excessive back-and-forth motion.

Another notable characteristic is the ease of use. The Graco TI13586A and TI13585A include an easy-to-operate control system that allows users to adjust the pressure settings, ensuring optimal spray control for various painting materials and techniques. This versatility is complemented by the FlexLiner container system, which reduces waste and allows for easy cleaning between jobs.

In terms of portability, these models are designed with mobility in mind. The lightweight construction, along with a durable cart that features large wheels, makes it easy to transport the sprayers to different job sites. Whether you're navigating stairs or uneven terrain, the design ensures that transportation remains hassle-free.

Both models are compatible with a variety of coatings, including latex paints, stains, and sealers, enhancing their adaptability for numerous applications. They also leverage Graco's proven Airless Technology, which ensures a consistent finish by using a piston pump system that allows for continuous operation without the risk of clogging. This technology results in faster project completion times, which is a significant advantage for contractors on a tight schedule.

Additionally, safety features such as a settings lock and the built-in pressure relief valve contribute to user protection while enhancing the overall painting experience. This focus on safety and efficiency ensures that both the TI13586A and TI13585A maintain Graco's reputation for quality and reliability in the airless spraying market.

In summary, both the Graco TI13586A and TI13585A represent powerful, user-friendly solutions for quality airless painting. Their effective motor, adjustable pressure settings, portability, and compatibility with various materials make them excellent choices for anyone looking to achieve professional-level results with ease and efficiency.
Top Page Image Contents