Graco ti13586a, ti13585a important safety instructions Flush Spray Gun, Position Air Cap

Page 15

KEY

N Cylinder Air Inlet: accepts 1/4 in. (6.3 mm) O.D. tubing

P Atomization Air Inlet: 3/8 in, (9.5 mm) O.D. tubing

R Fan Air Inlet: 3/8 in. (9.5 mm) O.D. tubing

S Fluid Inlet: 1/4 npsm

T Fluid Outlet (circulating gun only): 1/4 npsm

Side Mounted Manifold Ports

N

T (or S)

S (or T)

FAN ATOM

CYL

ti8096a

RP

Bottom Mounted Manifold Ports

N

R FAN ATOM P

CYL

T (or S)

S (or T)

 

 

ti8097a

FIG. 8: Manifold Ports

 

 

 

Setup

Flush Spray Gun

Before running any paint through the spray gun:

1.Flush the gun with a solvent that is compat- ible with the fluid to be sprayed, using the lowest possible fluid pressure and a grounded metal container.

2.Perform Pressure Relief Procedure; see page 18.

Position Air Cap

Air caps are factory-set with the alignment pin

(A)set to a vertical spray pattern. To change the air cap to a horizontal spray pattern, use a 1/6 in. hex wrench to unscrew the alignment pin (A) and relocate it to the horizontal spray pattern hole. When relocating the pin use low strength thread locker. Torque to 1.5-2.5 in-lb (0.2-0.3 N•m). Do not overtighten. Refer to FIG. 9.

ti8171a

Vertical Pattern

A

Horizontal Pattern

ti8170a

ti8172a

FIG. 9: Position Air Cap

313516G

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Automatic AirPro Spray Guns Important Safety InstructionsModels ContentsFire and Explosion Hazard Pressurized Equipment Hazard General Metal Applications Selection ChartsHvlp Guns High Wear ApplicationsWood Applications Gun SelectionProper Needle/Nozzle Selection Air CapsConventional Guns Atomizing Air Fan Air Air FlowMaximum HVLP/Compliant inlet manifold pressure Circulating System InstallationVentilate Spray Booth Configure Gun and ManifoldGround System Install Air FittingsMount Gun Reciprocating Arm Rod MountStationary Support Retrofit Adapter Plate Mount Retrofit Adapter PlateSetup Connect Air LineConnect Fluid Hose Position Air Cap Flush Spray GunAdjust Spray Pattern Suggested Starting Settings AtomizationFan Air psi Air Pressure Regulator Incorrect Pressure Relief ProcedureOperation Apply FluidDaily Gun Care Clean and Flush Gun General System MaintenanceTroubleshooting General TroubleshootingProblem Cause Solution Spray Pattern Troubleshooting Disassembly ServicePart No A749 Gun Shown Fluid packings ReassemblyParts Gasket General Metal Applications Repair KitsWood Applications High Wear Applications114101 103 107 105108 Part No C342 Side Fluid Ports and Fan Adjustment Valve107 101 114 103 106 Accessories Tips Hvlp Pressure Verification KitInline Fluid Filter 24B707 Spray Tip FiltersDimensions Manifold Models 288217 or 288218, All Gun ModelsManifold Model 288221, All Gun Models Manifold Model 288160 or 288211, All Gun Models Manifold Model 288223 or 24C342, All Gun ModelsMounting Hole Layouts 23.4 mm 10.2 mm 53.3 mm 50 in .7 mm mounting hole 216 225 58.4 mm Retrofit Adapter Plate Technical Data Triggering SpeedSound Data Graco Information Graco Standard Warranty

ti13586a, ti13585a specifications

The Graco TI13586A and TI13585A are advanced airless paint sprayers designed for both professional contractors and serious DIY enthusiasts. These models stand out for their ability to deliver high-quality finishes quickly and efficiently, making them ideal for a wide range of painting tasks, from residential projects to large-scale commercial applications.

One of the main features of the Graco TI13586A and TI13585A is their powerful motor. These sprayers come equipped with a robust 0.75 HP pump that can generate high pressure, allowing for thorough and consistent coverage on various surfaces. This motor works efficiently to atomize the paint, producing a fine spray pattern essential for achieving a smooth finish without the need for excessive back-and-forth motion.

Another notable characteristic is the ease of use. The Graco TI13586A and TI13585A include an easy-to-operate control system that allows users to adjust the pressure settings, ensuring optimal spray control for various painting materials and techniques. This versatility is complemented by the FlexLiner container system, which reduces waste and allows for easy cleaning between jobs.

In terms of portability, these models are designed with mobility in mind. The lightweight construction, along with a durable cart that features large wheels, makes it easy to transport the sprayers to different job sites. Whether you're navigating stairs or uneven terrain, the design ensures that transportation remains hassle-free.

Both models are compatible with a variety of coatings, including latex paints, stains, and sealers, enhancing their adaptability for numerous applications. They also leverage Graco's proven Airless Technology, which ensures a consistent finish by using a piston pump system that allows for continuous operation without the risk of clogging. This technology results in faster project completion times, which is a significant advantage for contractors on a tight schedule.

Additionally, safety features such as a settings lock and the built-in pressure relief valve contribute to user protection while enhancing the overall painting experience. This focus on safety and efficiency ensures that both the TI13586A and TI13585A maintain Graco's reputation for quality and reliability in the airless spraying market.

In summary, both the Graco TI13586A and TI13585A represent powerful, user-friendly solutions for quality airless painting. Their effective motor, adjustable pressure settings, portability, and compatibility with various materials make them excellent choices for anyone looking to achieve professional-level results with ease and efficiency.
Top Page Image Contents