Graco ti13586a, ti13585a important safety instructions Air Pressure Regulator

Page 17

NOTE: HVLP and Compliant Gun Limits

HVLP Guns: local laws may limit the maximum pressure to 10 psi (70 kPa, 0.7 bar) at the air cap for compliance. See the table on page 7 for maximum HVLP/Compliant manifold inlet pressures. To measure pressure at the air cap, use the appropriate HVLP Pressure Verifica- tion Kit. See Accessories, page 34.

Compliant Guns: See the table on page 7 for maximum HVLP/Compliant manifold inlet pres- sures.

F

ti01997

FIG. 11: Air Pressure Regulator

3.Test the spray pattern atomization while keeping the gun a consistent distance, about 6 to 8 inches (150 to 200 mm), from the test piece.

Check the atomization quality. Increase the gun atomizing air supply pressure with the air pressure regulator in 5 psi (34 kPa, 0.3 bar) increments until you obtain the desired atomization.

NOTE: For the best transfer efficiency, use the lowest setting needed to achieve desired finish quality.

Setup

4.If the spray pattern is too wide or split, reduce the fan air pressure (or slightly close the fan adjustment valve on manifold 288223).

To further control the spray pattern of air- spray guns only, use an alternate air cap. For a list of available air caps, refer to Accessories, page 34.

NOTE: Reducing the fan air pressure to 0 psi (or fully closing the fan adjustment valve) will produce a round pattern.

313516G

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Automatic AirPro Spray Guns Important Safety InstructionsModels ContentsFire and Explosion Hazard Pressurized Equipment Hazard General Metal Applications Selection ChartsWood Applications High Wear ApplicationsGun Selection Hvlp GunsConventional Guns Proper Needle/Nozzle SelectionAir Caps Atomizing Air Fan Air Air FlowMaximum HVLP/Compliant inlet manifold pressure Ventilate Spray Booth InstallationConfigure Gun and Manifold Circulating SystemGround System Install Air FittingsStationary Support Mount GunReciprocating Arm Rod Mount Retrofit Adapter Plate Mount Retrofit Adapter PlateConnect Fluid Hose SetupConnect Air Line Position Air Cap Flush Spray GunFan Air psi Adjust Spray PatternSuggested Starting Settings Atomization Air Pressure Regulator Operation Pressure Relief ProcedureApply Fluid IncorrectDaily Gun Care Clean and Flush Gun General System MaintenanceProblem Cause Solution TroubleshootingGeneral Troubleshooting Spray Pattern Troubleshooting Disassembly ServicePart No A749 Gun Shown Fluid packings ReassemblyParts Gasket General Metal Applications Repair KitsWood Applications High Wear Applications114101 103 107 105108 Part No C342 Side Fluid Ports and Fan Adjustment Valve107 101 114 103 106 Accessories Inline Fluid Filter 24B707 Hvlp Pressure Verification KitSpray Tip Filters TipsManifold Model 288221, All Gun Models DimensionsManifold Models 288217 or 288218, All Gun Models Manifold Model 288160 or 288211, All Gun Models Manifold Model 288223 or 24C342, All Gun ModelsMounting Hole Layouts 23.4 mm 10.2 mm 53.3 mm 50 in .7 mm mounting hole 216 225 58.4 mm Retrofit Adapter Plate Sound Data Technical DataTriggering Speed Graco Information Graco Standard Warranty

ti13586a, ti13585a specifications

The Graco TI13586A and TI13585A are advanced airless paint sprayers designed for both professional contractors and serious DIY enthusiasts. These models stand out for their ability to deliver high-quality finishes quickly and efficiently, making them ideal for a wide range of painting tasks, from residential projects to large-scale commercial applications.

One of the main features of the Graco TI13586A and TI13585A is their powerful motor. These sprayers come equipped with a robust 0.75 HP pump that can generate high pressure, allowing for thorough and consistent coverage on various surfaces. This motor works efficiently to atomize the paint, producing a fine spray pattern essential for achieving a smooth finish without the need for excessive back-and-forth motion.

Another notable characteristic is the ease of use. The Graco TI13586A and TI13585A include an easy-to-operate control system that allows users to adjust the pressure settings, ensuring optimal spray control for various painting materials and techniques. This versatility is complemented by the FlexLiner container system, which reduces waste and allows for easy cleaning between jobs.

In terms of portability, these models are designed with mobility in mind. The lightweight construction, along with a durable cart that features large wheels, makes it easy to transport the sprayers to different job sites. Whether you're navigating stairs or uneven terrain, the design ensures that transportation remains hassle-free.

Both models are compatible with a variety of coatings, including latex paints, stains, and sealers, enhancing their adaptability for numerous applications. They also leverage Graco's proven Airless Technology, which ensures a consistent finish by using a piston pump system that allows for continuous operation without the risk of clogging. This technology results in faster project completion times, which is a significant advantage for contractors on a tight schedule.

Additionally, safety features such as a settings lock and the built-in pressure relief valve contribute to user protection while enhancing the overall painting experience. This focus on safety and efficiency ensures that both the TI13586A and TI13585A maintain Graco's reputation for quality and reliability in the airless spraying market.

In summary, both the Graco TI13586A and TI13585A represent powerful, user-friendly solutions for quality airless painting. Their effective motor, adjustable pressure settings, portability, and compatibility with various materials make them excellent choices for anyone looking to achieve professional-level results with ease and efficiency.
Top Page Image Contents