Graco ti13585a, ti13586a important safety instructions Spray Pattern Troubleshooting

Page 22

Troubleshooting

Problem

Cause

Solution

 

 

 

 

 

 

 

Fluid needle will not trigger.

Loose or missing fluid needle stop

Replace stop or tighten setscrew.

 

 

(29) or setscrew (30).

 

 

 

Air leaking around piston (3).

Replace o-ring (8) or piston.

 

Swollen piston o-ring (8).

Replace o-ring. Do not immerse

 

 

piston in solvent.

 

Insufficient air pressure on trigger.

Increase air pressure or clean air

 

 

line.

 

Plug (19) is in incorrect fluid port.

Move plug to fluid port consistent

 

 

with manifold plumbing, unless

 

 

you are using gun in a circulating

 

 

system. If you are, all fluid ports in

 

 

gun and on manifold should be

 

 

open.

 

 

 

Fluid does not shut off.

Worn o-ring (11) or (9).

Replace o-ring.

 

Piston cap (4) not fully tightened.

Tighten piston cap until it bottoms

 

 

out.

 

Spring (6) not in place.

Check spring position.

 

Swollen piston o-ring (8).

Replace o-ring. Do not immerse

 

 

piston in solvent.

 

 

 

 

Spray Pattern Troubleshooting

Problem

Cause

Solution

 

 

 

 

 

 

 

Fluid flow is fluttering while spray-

Fluid nozzle is not tight enough.

Tighten fluid nozzle to 60 in-lb

ing.

 

(6.8 N•m).

 

O-ring (36) is missing or dam-

Replace o-ring.

 

aged.

 

 

 

Fluid filter is clogged.

Check fluid filter.

 

 

 

Fluid flow fades while spraying

Fluid pressure is too low, causing

Raise fluid pressure at source or

high viscosity fluids.

fluid flow to reduce when gun is

use a smaller fluid nozzle.

 

elevated.

 

 

 

 

 

Pattern becomes off-set or heavy

Air cap horn holes plugged or

Clean air cap horn holes with

on ends.

damaged.

non-metallic item such as a tooth-

 

 

pick, or replace air cap.

 

 

 

Gun fluid pressure is too high with

Using needle/nozzle kit with too

Use needle/nozzle kit with larger

gun triggered.

small orifice.

orifice.

 

 

 

Fluid system will not operate at

There is no fluid regulator, or air

Add low pressure fluid regulator,

low enough fluid pressure [below

regulator on pressure pot is not

or add more sensitive low pres-

10 psi (70 kPa, 0.7 bar)].

sensitive enough at low pressures.

sure air regulator on pressure pot.

 

 

 

 

22

313516G

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Important Safety Instructions Automatic AirPro Spray GunsContents ModelsFire and Explosion Hazard Pressurized Equipment Hazard Selection Charts General Metal ApplicationsGun Selection High Wear ApplicationsWood Applications Hvlp GunsAir Caps Proper Needle/Nozzle SelectionConventional Guns Air Flow Atomizing Air Fan AirMaximum HVLP/Compliant inlet manifold pressure Configure Gun and Manifold InstallationVentilate Spray Booth Circulating SystemInstall Air Fittings Ground SystemReciprocating Arm Rod Mount Mount GunStationary Support Retrofit Adapter Plate Retrofit Adapter Plate MountConnect Air Line SetupConnect Fluid Hose Flush Spray Gun Position Air CapSuggested Starting Settings Atomization Adjust Spray PatternFan Air psi Air Pressure Regulator Apply Fluid Pressure Relief ProcedureOperation IncorrectDaily Gun Care General System Maintenance Clean and Flush GunGeneral Troubleshooting TroubleshootingProblem Cause Solution Spray Pattern Troubleshooting Service DisassemblyPart No A749 Gun Shown Reassembly Fluid packingsParts Gasket Repair Kits General Metal ApplicationsHigh Wear Applications Wood Applications114101 103 107 105108 Side Fluid Ports and Fan Adjustment Valve Part No C342107 101 114 103 106 Accessories Spray Tip Filters Hvlp Pressure Verification KitInline Fluid Filter 24B707 TipsManifold Models 288217 or 288218, All Gun Models DimensionsManifold Model 288221, All Gun Models Manifold Model 288223 or 24C342, All Gun Models Manifold Model 288160 or 288211, All Gun ModelsMounting Hole Layouts 23.4 mm 10.2 mm 53.3 mm 50 in .7 mm mounting hole 216 225 58.4 mm Retrofit Adapter Plate Triggering Speed Technical DataSound Data Graco Standard Warranty Graco Information

ti13586a, ti13585a specifications

The Graco TI13586A and TI13585A are advanced airless paint sprayers designed for both professional contractors and serious DIY enthusiasts. These models stand out for their ability to deliver high-quality finishes quickly and efficiently, making them ideal for a wide range of painting tasks, from residential projects to large-scale commercial applications.

One of the main features of the Graco TI13586A and TI13585A is their powerful motor. These sprayers come equipped with a robust 0.75 HP pump that can generate high pressure, allowing for thorough and consistent coverage on various surfaces. This motor works efficiently to atomize the paint, producing a fine spray pattern essential for achieving a smooth finish without the need for excessive back-and-forth motion.

Another notable characteristic is the ease of use. The Graco TI13586A and TI13585A include an easy-to-operate control system that allows users to adjust the pressure settings, ensuring optimal spray control for various painting materials and techniques. This versatility is complemented by the FlexLiner container system, which reduces waste and allows for easy cleaning between jobs.

In terms of portability, these models are designed with mobility in mind. The lightweight construction, along with a durable cart that features large wheels, makes it easy to transport the sprayers to different job sites. Whether you're navigating stairs or uneven terrain, the design ensures that transportation remains hassle-free.

Both models are compatible with a variety of coatings, including latex paints, stains, and sealers, enhancing their adaptability for numerous applications. They also leverage Graco's proven Airless Technology, which ensures a consistent finish by using a piston pump system that allows for continuous operation without the risk of clogging. This technology results in faster project completion times, which is a significant advantage for contractors on a tight schedule.

Additionally, safety features such as a settings lock and the built-in pressure relief valve contribute to user protection while enhancing the overall painting experience. This focus on safety and efficiency ensures that both the TI13586A and TI13585A maintain Graco's reputation for quality and reliability in the airless spraying market.

In summary, both the Graco TI13586A and TI13585A represent powerful, user-friendly solutions for quality airless painting. Their effective motor, adjustable pressure settings, portability, and compatibility with various materials make them excellent choices for anyone looking to achieve professional-level results with ease and efficiency.
Top Page Image Contents