Graco ti13585a, ti13586a important safety instructions Part No A749 Gun Shown

Page 24

Service

13.Remove all o-rings from the piston (3) and stems (T). Check that the stems are solidly in place. If they are loose, replace the entire piston assembly (3).

14.Perform the following applicable step:

a.Non-circulating guns: Remove the fluid outlet port plug (19), and gasket (22) from the fluid housing (2). Remove the

o-ring (21) and backup (20) from the plug. See FIG. 21.

b. Circulating guns: Remove the gasket (22) from the fluid housing (2). See FIG. 21.

15.Clean all parts and replace any worn parts. When assembling, lubricate the threads with anti-seize lubricant.

Cutaway View:

 

 

T

8* 3 4 2 4

Part No. 24A749 Gun Shown

1 2

10* 3

11* 3

 

 

 

6

 

 

25

2

2

16 8

24

23 1

2

 

 

 

5a

9

5

36

ti8199a

Alternate Fluid Control Shown

7

 

 

 

30 6

7

29

 

 

9 3

3 3

 

 

46 3

10

12*

 

ti13592b

 

 

 

 

45 (x 2) 3

SERVICE NOTES:

1Torque to 35-45 in-lb (4.0-5.1 N•m).

2Lubricate threads with anti-seize lubricant.

3Lubricate with light-weight oil.

4Tighten cap (4) until it bottoms out.

6Apply semi-permanent anaerobic sealant.

7Torque to 6.5-7.5 in-lb (0.73-0.85 N•m).

8Torque to 95-105 in-lb (10.7-11.8 N•m).

9Apply semi-permanent anaerobic sealant to two threads at end of needle shaft.

10Step in spacer (46) must face into packing nut.

FIG. 19

24

313516G

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Important Safety Instructions Automatic AirPro Spray GunsContents ModelsFire and Explosion Hazard Pressurized Equipment Hazard Selection Charts General Metal ApplicationsHigh Wear Applications Wood ApplicationsGun Selection Hvlp GunsProper Needle/Nozzle Selection Air CapsConventional Guns Air Flow Atomizing Air Fan AirMaximum HVLP/Compliant inlet manifold pressure Installation Ventilate Spray BoothConfigure Gun and Manifold Circulating SystemInstall Air Fittings Ground SystemMount Gun Reciprocating Arm Rod MountStationary Support Retrofit Adapter Plate Retrofit Adapter Plate MountSetup Connect Air LineConnect Fluid Hose Flush Spray Gun Position Air CapAdjust Spray Pattern Suggested Starting Settings AtomizationFan Air psi Air Pressure Regulator Pressure Relief Procedure OperationApply Fluid IncorrectDaily Gun Care General System Maintenance Clean and Flush GunTroubleshooting General TroubleshootingProblem Cause Solution Spray Pattern Troubleshooting Service DisassemblyPart No A749 Gun Shown Reassembly Fluid packingsParts Gasket Repair Kits General Metal ApplicationsHigh Wear Applications Wood Applications114101 103 107 105108 Side Fluid Ports and Fan Adjustment Valve Part No C342107 101 114 103 106 Accessories Hvlp Pressure Verification Kit Inline Fluid Filter 24B707Spray Tip Filters TipsDimensions Manifold Models 288217 or 288218, All Gun ModelsManifold Model 288221, All Gun Models Manifold Model 288223 or 24C342, All Gun Models Manifold Model 288160 or 288211, All Gun ModelsMounting Hole Layouts 23.4 mm 10.2 mm 53.3 mm 50 in .7 mm mounting hole 216 225 58.4 mm Retrofit Adapter Plate Technical Data Triggering SpeedSound Data Graco Standard Warranty Graco Information

ti13586a, ti13585a specifications

The Graco TI13586A and TI13585A are advanced airless paint sprayers designed for both professional contractors and serious DIY enthusiasts. These models stand out for their ability to deliver high-quality finishes quickly and efficiently, making them ideal for a wide range of painting tasks, from residential projects to large-scale commercial applications.

One of the main features of the Graco TI13586A and TI13585A is their powerful motor. These sprayers come equipped with a robust 0.75 HP pump that can generate high pressure, allowing for thorough and consistent coverage on various surfaces. This motor works efficiently to atomize the paint, producing a fine spray pattern essential for achieving a smooth finish without the need for excessive back-and-forth motion.

Another notable characteristic is the ease of use. The Graco TI13586A and TI13585A include an easy-to-operate control system that allows users to adjust the pressure settings, ensuring optimal spray control for various painting materials and techniques. This versatility is complemented by the FlexLiner container system, which reduces waste and allows for easy cleaning between jobs.

In terms of portability, these models are designed with mobility in mind. The lightweight construction, along with a durable cart that features large wheels, makes it easy to transport the sprayers to different job sites. Whether you're navigating stairs or uneven terrain, the design ensures that transportation remains hassle-free.

Both models are compatible with a variety of coatings, including latex paints, stains, and sealers, enhancing their adaptability for numerous applications. They also leverage Graco's proven Airless Technology, which ensures a consistent finish by using a piston pump system that allows for continuous operation without the risk of clogging. This technology results in faster project completion times, which is a significant advantage for contractors on a tight schedule.

Additionally, safety features such as a settings lock and the built-in pressure relief valve contribute to user protection while enhancing the overall painting experience. This focus on safety and efficiency ensures that both the TI13586A and TI13585A maintain Graco's reputation for quality and reliability in the airless spraying market.

In summary, both the Graco TI13586A and TI13585A represent powerful, user-friendly solutions for quality airless painting. Their effective motor, adjustable pressure settings, portability, and compatibility with various materials make them excellent choices for anyone looking to achieve professional-level results with ease and efficiency.
Top Page Image Contents