Graco Inc PRO 5000, 307-712, 218-745 manual Disc Regulator ORing Replacement

Page 25

SERVICE

Disc￿ Regulator￿ O)Ring￿ Replacement

KEY

 

 

 

 

 

1

Gun￿ ￿ody

 

87

O:Ring

￿. Unscrew￿ the￿ turbine￿ air￿ line￿ from￿ the￿ adapter￿ ￿￿6￿.

Regulator￿ ￿isk

88

￿ir￿ Valve

See￿ Fig￿ 22.

3

85

O-Ring

 

89

Washer

 

 

 

86

￿dapter

 

90

￿ap￿ Screw

2. Remove￿ the￿ cap￿ screw￿ ￿￿￿￿￿ and￿ washer￿ ￿￿￿￿￿ from

 

 

 

 

the￿ gun￿ body￿ ￿￿￿.

 

￿6

 

 

 

 

 

 

 

 

3. Pull￿ the￿ adapter￿ ￿￿6￿￿￿ with￿ the￿ air￿ valve￿ ￿￿￿￿￿￿ out￿ of

3

￿￿

 

the￿ gun￿ body.

 

 

 

 

 

￿￿

￿

￿. Unscrew￿ the￿ adapter￿ ￿￿6￿￿ from￿ the￿ air￿ valve￿ ￿￿￿￿￿

 

￿￿

 

 

and￿ remove￿ the￿ disk￿ regulator￿ ￿3￿.

 

 

￿. ￿lean￿ and￿ inspect￿ parts￿ for￿ wear￿ or￿ damage￿ and replace￿ if￿ necessary.

6.￿lean￿ and￿ inspect￿ the￿ two￿ o:rings￿ ￿￿￿￿￿ and￿ one￿ o: ring￿ ￿￿￿￿￿ on￿ the￿ air￿ valve.￿ Replace￿ if￿ necessary.￿ Lu: bricate￿ the￿ o:rings￿ with￿ petroleum￿ jelly.

￿. Install￿ the￿ disc￿ regulator￿ ￿3￿￿ into￿ the￿ air￿ valve￿ ￿￿￿￿￿ so its￿ beveled￿ surface￿ faces￿ into￿ the￿ gun.

￿. Screw￿ the￿ adapter￿ ￿￿6￿￿ into￿ the￿ air￿ valve￿ ￿￿￿￿￿￿ and

install￿ the￿ air￿ valve￿ into￿ the￿ gun￿ body￿ ￿￿￿.

Fig￿ 22

 

￿. Screw￿ the￿ cap￿ screw￿ ￿￿￿￿￿￿ with￿ the￿ washer￿ ￿￿￿￿￿￿ into

the￿ gun￿ body￿ ￿￿￿.

KEY

￿￿

￿￿

￿￿. Screw￿ the￿ turbine￿ air￿ line￿ onto￿ the￿ adapter￿ ￿6￿￿.1

Gun￿ ￿ody

 

76

Muffler

 

77

Elbow

 

78

Tube

￿

Muffler￿ Replacement

￿. Remove￿ the￿ fan￿ air￿ valve￿ assembly￿ as￿ instructed￿ in Fan￿ Air￿ Valve￿ Replacement.

2.Remove￿ the￿ elbow￿ ￿￿6￿￿ with￿ the￿ tube￿ ￿￿￿￿￿ from￿ the gun￿ body￿ ￿￿￿.￿ See￿ Fig￿ 23.

3.With￿ a￿ hook￿￿ remove￿ the￿ muffler￿ ￿￿￿￿￿ from￿ the￿ gun body￿ and￿ replace￿ with￿ a￿ new￿ muffler.

￿. Install￿ the￿ elbow￿ ￿￿6￿￿ in￿ the￿ gun￿ body.

￿. Install￿ the￿ fan￿ air￿ valve￿ assembly￿ as￿ instructedFan ￿ in￿ Air￿ Valve￿ Replacement.

￿￿

￿￿ ￿6

Fig￿ 23

307-712 25

Image 25
Contents Rev P Automatic MID-RANGE ElectrostaticPart Number 218±745, Series B This manual contains Important  Terms Table of ContentsEquipment Misuse Hazard Hose SafetyHazardous Fluid Hazard Ventilate the Spray Booth Flushing and Cleaning SafetyFire or Explosion Hazard HOW the Electrostatic AIR Spray GUN WorksVentilate the Spray Booth Typical InstallationNON±HAZARDOUS Area KEY Hazardous AreaMount the Gun InstallationCheck the Electrical Grounding Installing Optional Remote Fan Air AdapterOperation Operating ChecklistFilter the Fluid Spraying OperationAccessories Adjust the Spray PatternDaily Care and Cleaning MaintenanceFlush the Spray Gun GUN in SolventEquipment needed To Clean or Change Air Cap and Fluid NozzleProblem Cause Solution Improper Spray Pattern Spray Pattern Troubleshooting ChartProblem Cause Solution GUN Operation Troubleshooting ChartSee Check the Electrical Grounding Electrical Troubleshooting ChartElectrical Tests Test Power Supply ResistanceTest Gun Resistance Test Resistor Stud Resistance Gun Disassembly ServiceGun Assembly Note Electrode ReplacementTo install the resistor stud Resistor Stud ReplacementBarrel Removal Fluid Needle Packing Replacement66b Service Power Cartridge Replacement Turbine Alternator RemovalFan Air Valve Replacement Piston Removal and Repair Disc Regulator ORing Replacement Ref No 66, Tool Kit Ref No Power CartridgeDetail a Old/New Style Resistor Stud and Electrode Parts ListDescription Qty KitsService Information Technical DataHOW to Order Replacement Parts Assembly Changed Status No. Part No NameHigh Volume AIR Regulator 206±199 AccessoriesGrounded AIR Supply Hose AIR Hose Adapter 185±493Filter AIR or Paint 202±271 Remote Switch & Signal Light 728±386 Control Panel 218±394Electrostatic System 231±035 Electrostatic System 231±036Warranty Graco Warranty and DisclaimersImportant Phone Numbers To you 1±800±328±0211 Toll Free