Roper M6707-1-1 manual Super PRO GUN, See Figs .5 & 9.6 for exploded schematic drawings

Page 9

5.Set the 9203-2-1 (Compression Spring) into the spring seat located in the upper cavity of the 5105-1-1 (Gun Handle).

6.Place the small pinhole in the 5105-3-1 (Slide Valve) over the pin through the 5105-14-1 (Trigger Stem), and push down compressing the spring into the handle cavity.

7.Place the 5105-4-1 (Porting Plate Gasket) over the screws, matching the slot to the slot in the 5105-1-1 (Gun Handle).

8.Lightly lubricate the flat side of the 5105-5-1 (Porting Plate) with 6706-3-1 (Pro Gun Oil) and push it over the 5105-3-1 (Slide Valve) keeping the Slide Valve connected to the 7203-4-9 (Slotted Spring Pin) in the 5105-14-1 (Trigger Stem).

NOTE

Theslotinthesideofthe5105-5-1(PortingPlate)mustlineupwiththeslot inthe5105-1-1(GunHandle).

9.Set the 5105-6-1 (Toggle Washer) into the washer seal seat of the 5105-5-1 (Porting Plate) large side down.

10.Set the 5105-7-1 (Cylinder Gasket) over the screws, matching the slots in the 5105-5-1 (Porting Plate)

11.Carefully position the 5106-00-01 (Gun Actuator Assembly) over the 5105-00-01 (Gun Handle Assembly) and fasten with the two 5105-12-1 (Front Screws) and the 5105-13-1 (Rear Screws).

12.If necessary, adjust the 5105-8-1 (Trigger Lock) by pulling the

5105-16-1 (Trigger) to “full out”, then flip the Trigger Lock up until it hits the smallest part of the 5105-11-1 (Trigger Lock Screw). Loosen the 7102-6-4 (Socket Cup Point Set Screw) and adjust the Trigger Lock Screw until it clears with minor interference. The locking legs on the Trigger Lock Screw must be vertical. The Trigger Lock should lock the trigger in both the open and closed position. Once adjusted, tighten the 7102-6-4 (Socket Cup Point Set Screw).

13.With the two 7102-8-8 (Slotted Pan Head Screws), mount the 5105-2-1 (Trigger Guard).

SUPER PRO GUN II

Handle Assembly 5110-7-1

See Figs. 9.5 & 9.6 for exploded schematic drawings

1.Carefully install the 5105-9-1 (Trigger Nut Seal) over the 5105-10-1 (Trigger Nut).

2.Coat the 7304-4-1 (Lip Seal) with 6706-3-1 (Pro Gun Oil), and push it into the 5105-10-1 (Trigger Nut).

4

SUPER PRO GUN &

 

SUPER PRO GUN II

Image 9
Contents Super PRO GUN & Super PRO GUN Corporate HQ & Mfg Manufacturing Super PRO GUN & Super PRO GUNTable of Contents Super PRO GUN Repair Kit Super PRO GUN II Repair Kit See Figs .1 & 9.2 for exploded schematic drawings Actuator AssemblySuper PRO GUN See Figs .3 & 9.4 for exploded schematic drawings Handle AssemblySuper PRO GUN See Figs .5 & 9.6 for exploded schematic drawingsSuper PRO GUN Super PRO GUN Gun Block Assembly Flush Valve AssemblySee Figs .9 9.12 for exploded schematic drawings Gun Block Assembly Super PRO GUN Super PRO GUN Super PRO GUN Super PRO GUN Super PRO GUN See Figs .13 9.20 for exploded schematic drawings SuperCutter AssemblyRotor Assembly Rubber Roll Assembly Rubber Roll Adjustment Idler Adjustment Actuator Disassembly Handle Disassembly Handle Disassembly Gun Block Disassembly Flush Valve Disassembly Procedures Rubber Roll Disassembly SuperCutter DisassemblyRotor Disassembly Assembly Drawings Super PRO GUN Super PRO GUN Super PRO GUN Super PRO GUN Super PRO GUN Super PRO GUN Super PRO GUN Super PRO GUN Super PRO GUN Super PRO GUN Super PRO GUN Super PRO GUN Super PRO GUN Super PRO GUN Super PRO GUN Super PRO GUN Super PRO GUN Super PRO GUN Super PRO GUN Super PRO GUN Super PRO GUN Super PRO GUN Super PRO GUN & Super PRO GUN Super PRO GUN & Super PRO GUN Corporate HQ & Mfg Manufacturing/Sales