Digitrex 3-3000-00a-F manual DigiTrak Receiver Side View, DigiTrak Receiver Top View

Page 13

®

DIGITAL CONTROL INCORPORATED

Receiver

Handle

Speaker

Trigger

Display

 

Temperature

 

 

Windows

 

 

 

& Distance

 

 

 

Conversion

 

 

 

Chart

 

 

 

Battery

 

 

Depth/Locating

Compartment

 

 

Antenna Screws

Back Panel

Front Panel

Pitch/Roll

Antenna Screws

DigiTrak Receiver – Side View

The DigiTrak Receiver is a hand-held unit used for loca- ting and tracking the transmitter. It receives and converts signals from the transmitter and displays the following information: pitch, roll, depth/distance, predicted depth, temperature, and battery status. The display windows are located on the top of the receiver.

Next to each DigiTrak display window are symbols or icons to help you identify the functions of each window (see table on next page). The icons below each window represent the pitch, roll, and depth/distance of the transmitter, which are displayed when the trigger is released, as shown by the trigger down icon. When the trigger is held in (trigger up), the top left window will display the signal strength and the top right window will display the temperature. Note the predicted depth icon below the bottom window. When the trigger is held in and the receiver is positioned at the front negative locate point (FNLP), the predicted depth of the transmitter at the FNLP is displayed in the bottom window. This predicted depth number will flash quickly and the bottom window will also show a solidly illuminated squiggle (“~”) to further set it apart from the depth display.

Trigger Up

Temperature

Signal

 

 

Strength

 

 

~

I5

Trigger

Down

 

 

Pitch

I I8

 

 

Roll

Depth

 

Predicted

 

 

Depth

NOTE: Should the trigger be held in at any location

DigiTrak Receiver – Top View

other than the FNLP, the predicted depth shown will not

Showing Display Window Icons

be valid.

DigiTrak® Mark III Operator’s Manual

5

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Mark III Directional Drilling Locating System Trademarks Table of Contents Remote Display System Remote Telemetry License Limited Warranty Safety Precautions Vii RememberViii Dear CustomerBasic DigiTrak Equipment IntroductionDigiTrak Directional Drilling Locating System Basic DigiTrak Operation IntroductionTechnical Support 3000-00b-F DigiTrak Receiver Side View ReceiverDigiTrak Receiver Top View Showing Display Window IconsDisplay Window Icons ReceiverFirmware Version Remote Channel Setting Depth Measurement Units Receiver Battery Voltage LCD TestOn/Off To turn the receiver onClicking vs. Holding the Trigger Receiving the Transmitter’s SignalsTo turn the receiver off To change the channel Changing the Receiver’s Channel SettingReceiver Battery Status Voltage Remaining Battery Status Display for Receiver and TransmitterChanging the Depth Measurement Units English vs. Metric To change the measurement unitsUltrasonic Function Temperature RangeUse of Ultrasonic Measurement To Determine Actual Depth Zeroing the Ultrasonics Calibrating the Receiver Determining 1-Point Calibration SignalDo not calibrate if To calibrate newer receivers Confirming Proper CalibrationReceiver Depth Antenna Plumb Line Using Depth Antenna Plumb Line to Mark Locate PointsSeries Firmware Functions Finding Firmware VersionRunning Time Meter Display Procedure for Observing the Predicted DepthHow a Transmitter Works TransmitterBatteriesAntenna Index Slot Back Front DigiTrak TransmitterBattery Status Display Temperature DisplayTemperature Overheat TransmitterVerifying Proper Fit of Transmitter in Housing Sleep Mode Automatic ShutoffHow Transmitter Should Fit in Housing Front End Cap of Transmitter Showing Temp Dot and Index Slot To install a transmitter in the housingSensitive-Pitch Transmitters Locating the TransmitterTransmitter as an Inclinometer Tips for drilling with a sensitive-pitch transmitterModel Type Length Signal Battery Temp Color Transmitter SpecificationsSerial Numbers Range Type RatingRemote Display Unit Remote Display SystemTransmitter Temperature and Battery Status On/Off and Setting the ChannelRemote Display Using DigiTrak Receiver for Remote Steering Setting up DigiTrak Receiver For Remote SteeringRemote Steering ~ I5 DataLog CapabilityDigiTrak Battery Charger Battery ChargerCharging a Battery Battery ChargerBattery Is Battery Charger Control PanelConditioning a Battery Manually Conditioning a Battery in the ChargerIndicator Lights and Meanings Setup for Discharging a Battery Manually3000-00f-F Shutdown Procedure Start-up ProcedureMoisture and Temperature Avoidance System Operating InstructionsGeneral Maintenance Optimal Operating TemperaturesSystem Operation Electrical Interference/Background Noise Check Signal InterferenceSuggestions for Dealing with Interference Signal InterferenceSelf-Test for Mark III Receivers Operational TestsReceiver Balance Check Receiver Gain Test Operational TestsTransmitter Tests Transmitter Distance Color Transmitter Signal Strength ValuesCurrent Draw Test Transmitter Salt Water Range TestTransmitter Model Average Current mA Transmitter Battery Tests 3000-00i-F Locating Mode Trigger Held Locating ModeLocating Locate Points Fnlp & Rnlp and Locate Line PLLHandling the Receiver LocatingSide View Using Plus/Minus +/- Indicators for Locating Using Plus/Minus Indicators for LocatingLocating the Transmitter from the Drill Finding the Rear Negative Locate Point Rnlp from the DrillPlus Changes To Minus Drill Fine Tuning Rnlp Location Walking Toward LeftFinding the Positive Locate Line PLL from the Drill Finding the Front Negative Locate Point Fnlp from the Drill Fine Tuning Fnlp Walking Toward LeftFinding the Transmitter and Its Depth Method for Confirming Position Locating the Transmitter from the FrontLocating the Transmitter from the Front Method for Confirming PositionOff-Track Locating Locating on the FlyOff-Track Locating Four-Turn Technique Splitting the Front and Rear Negative Locate PointsTo find the Fnlp or the Rnlp Pitch Divider Calculating Depth Based on Distance Between Fnlp & RnlpCalculating Depth from Pitch Running off Pitch or Calculating Depth from PitchAntenna Configuration Transmitter’s Signal ShapeSignal Reception Elliptical Shape of Transmitter Signal FieldPositive Locate Line Above Transmitter Front and Rear Negative Locate PointsOrientation of Field Lines with Respect to Antennas 3000-00j-F DigiTrak Cable Transmitter System Cable Transmitter SystemLabel Indicating Cable-Ready Remote Display Cable TransmitterCable Transmitter Power Supply Connected to Remote Display Power SupplyCable Transmitter Adding Batteries in Series Remote Display with Cable Transmitter CapabilityOperation Viewing the Cable System Battery StatusProblem/Concern Causes/Solutions Section to Consult TroubleshootingTroubleshooting Troubleshooting Troubleshooting Troubleshooting 3000-00l-F Glossary Glossary Remote Display Start-up = Power-up = Boot-upRoll Set the UltrasonicsUltrasonic Transducers Ultrasonic FunctionAppendix Percent Depth Increase 100 AppendixPercent of Grade to Degree Conversions Pitch Transmitters Percent Degree Degree to Percent of Grade Conversions Pitch Transmitters Degrees Percent 10.0 Calculating Depth Based on Distance Between Fnlp and Rnlp 3000-00n-F Remote Telemetry License 3000-00o-F Limited Warranty Warranty Claim Procedures
Top Page Image Contents