Digitrex 3-3000-00a-F manual Appendix

Page 81

®

DIGITAL CONTROL INCORPORATED

Appendix

The information and tables contained in this appendix provide further assistance for confirming the posi- tion of the Transmitter. The following information is provided:

Depth Increase in Inches per 10-foot Rod

Percent of Grade to Degree Conversions (1% Pitch Transmitters)

Percent of Grade to Degree Conversions (0.1% Pitch Transmitters or Sensitive Pitch) Degree to Percent of Grade Conversions (1% Pitch Transmitters)

Degree to Percent of Grade Conversions (0.1% Pitch Transmitters)

Calculating Depth Based on Distance Between FNLP and RNLP

DigiTrak® Mark III Operator’s Manual

73

Image 81

Contents Mark III Directional Drilling Locating System Trademarks Table of Contents Remote Display System Remote Telemetry License Limited Warranty Safety Precautions Vii RememberViii Dear CustomerIntroduction Basic DigiTrak EquipmentDigiTrak Directional Drilling Locating System Basic DigiTrak Operation IntroductionTechnical Support 3000-00b-F DigiTrak Receiver Side View ReceiverDigiTrak Receiver Top View Showing Display Window IconsDisplay Window Icons ReceiverFirmware Version Remote Channel Setting Depth Measurement Units Receiver Battery Voltage LCD TestOn/Off To turn the receiver onReceiving the Transmitter’s Signals Clicking vs. Holding the TriggerTo turn the receiver off To change the channel Changing the Receiver’s Channel SettingReceiver Battery Status Voltage Remaining Battery Status Display for Receiver and TransmitterChanging the Depth Measurement Units English vs. Metric To change the measurement unitsTemperature Range Ultrasonic FunctionUse of Ultrasonic Measurement To Determine Actual Depth Zeroing the Ultrasonics Determining 1-Point Calibration Signal Calibrating the ReceiverDo not calibrate if To calibrate newer receivers Confirming Proper CalibrationReceiver Depth Antenna Plumb Line Using Depth Antenna Plumb Line to Mark Locate PointsSeries Firmware Functions Finding Firmware VersionRunning Time Meter Display Procedure for Observing the Predicted DepthHow a Transmitter Works TransmitterBatteriesAntenna Index Slot Back Front DigiTrak TransmitterBattery Status Display Temperature DisplayTemperature Overheat TransmitterSleep Mode Automatic Shutoff Verifying Proper Fit of Transmitter in HousingHow Transmitter Should Fit in Housing Front End Cap of Transmitter Showing Temp Dot and Index Slot To install a transmitter in the housingSensitive-Pitch Transmitters Locating the TransmitterTransmitter as an Inclinometer Tips for drilling with a sensitive-pitch transmitterModel Type Length Signal Battery Temp Color Transmitter SpecificationsSerial Numbers Range Type RatingRemote Display Unit Remote Display SystemOn/Off and Setting the Channel Transmitter Temperature and Battery StatusRemote Display Setting up DigiTrak Receiver For Remote Steering Using DigiTrak Receiver for Remote SteeringRemote Steering ~ I5 DataLog CapabilityDigiTrak Battery Charger Battery ChargerCharging a Battery Battery ChargerBattery Is Battery Charger Control PanelConditioning a Battery Manually Conditioning a Battery in the ChargerIndicator Lights and Meanings Setup for Discharging a Battery Manually3000-00f-F Shutdown Procedure Start-up ProcedureMoisture and Temperature Avoidance System Operating InstructionsOptimal Operating Temperatures General MaintenanceSystem Operation Electrical Interference/Background Noise Check Signal InterferenceSuggestions for Dealing with Interference Signal InterferenceOperational Tests Self-Test for Mark III ReceiversReceiver Balance Check Operational Tests Receiver Gain TestTransmitter Tests Transmitter Distance Color Transmitter Signal Strength ValuesTransmitter Salt Water Range Test Current Draw TestTransmitter Model Average Current mA Transmitter Battery Tests 3000-00i-F Locating Mode Trigger Held Locating ModeLocating Locate Points Fnlp & Rnlp and Locate Line PLLLocating Handling the ReceiverSide View Using Plus/Minus +/- Indicators for Locating Using Plus/Minus Indicators for LocatingLocating the Transmitter from the Drill Finding the Rear Negative Locate Point Rnlp from the DrillFine Tuning Rnlp Location Walking Toward Left Plus Changes To Minus DrillFinding the Positive Locate Line PLL from the Drill Finding the Front Negative Locate Point Fnlp from the Drill Fine Tuning Fnlp Walking Toward LeftFinding the Transmitter and Its Depth Method for Confirming Position Locating the Transmitter from the FrontLocating the Transmitter from the Front Method for Confirming PositionLocating on the Fly Off-Track LocatingOff-Track Locating Splitting the Front and Rear Negative Locate Points Four-Turn TechniqueTo find the Fnlp or the Rnlp Pitch Divider Calculating Depth Based on Distance Between Fnlp & RnlpCalculating Depth from Pitch Running off Pitch or Calculating Depth from PitchAntenna Configuration Transmitter’s Signal ShapeSignal Reception Elliptical Shape of Transmitter Signal FieldFront and Rear Negative Locate Points Positive Locate Line Above TransmitterOrientation of Field Lines with Respect to Antennas 3000-00j-F DigiTrak Cable Transmitter System Cable Transmitter SystemLabel Indicating Cable-Ready Remote Display Cable TransmitterCable Transmitter Power Supply Connected to Remote Display Power SupplyCable Transmitter Adding Batteries in Series Remote Display with Cable Transmitter CapabilityOperation Viewing the Cable System Battery StatusProblem/Concern Causes/Solutions Section to Consult TroubleshootingTroubleshooting Troubleshooting Troubleshooting Troubleshooting 3000-00l-F Glossary Glossary Remote Display Start-up = Power-up = Boot-upRoll Set the UltrasonicsUltrasonic Transducers Ultrasonic FunctionAppendix Percent Depth Increase 100 AppendixPercent of Grade to Degree Conversions Pitch Transmitters Percent Degree Degree to Percent of Grade Conversions Pitch Transmitters Degrees Percent 10.0 Calculating Depth Based on Distance Between Fnlp and Rnlp 3000-00n-F Remote Telemetry License 3000-00o-F Limited Warranty Warranty Claim Procedures