Dell 7x0N manual =%=*2DC,+

5￿￿￿￿￿￿￿￿￿%%￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿8￿￿￿8"￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿,￿￿￿￿￿￿￿￿$￿￿￿'￿￿3￿￿￿￿￿￿￿￿￿￿￿￿￿￿&+￿4&'￿￿￿4￿8

5￿￿￿￿￿￿￿￿%%￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿8￿￿￿8"￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿$￿￿￿'￿￿3￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿&+￿4&'￿￿￿4￿

￿￿￿￿￿￿￿￿￿￿$￿%￿￿￿@￿￿￿￿3￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿&+￿4&'￿￿￿4￿

5￿0￿)*+￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿-￿￿￿￿￿41￿￿￿￿!￿￿￿￿

￿￿A￿2￿2￿￿￿￿2￿￿￿￿B￿￿￿￿￿￿￿￿￿￿￿￿￿!￿"￿

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿+￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿%￿@￿￿￿

5￿￿1$￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿!

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿!￿￿￿￿￿￿￿,￿)￿￿￿￿￿!-

To modify load balancing groups, use the uniconfig set failover command.

Syntax: The uniconfig set failover command has the following syntax:

￿￿￿'￿￿￿￿,￿%￿￿￿￿￿￿￿￿&￿￿￿C￿￿%￿￿￿￿￿￿￿￿￿=￿%￿￿￿￿'￿=￿￿*￿￿2￿'￿D￿C￿,￿￿￿+￿

￿￿￿￿￿￿￿￿￿D

-state static puts UNI load balancing in a static mode.

-group unit... specifies the load balancing group membership.

-state off disables load balancing and failover.

The option -state dynamic is the default.

Example: The following command disables load balancing and failover:

￿￿￿'￿￿￿￿,￿%￿￿￿￿￿￿￿￿&￿￿￿￿%￿￿￿￿￿￿￿￿￿

The arguments to the -groupparameter specify the ATM adapters (units) that should be logically assigned to a load balancing and failover group. If you specify a unit that has already been assigned to another group, the unit is automatically removed from the original group before being assigned to the new group.

Load balancing does not depend on any nonstandard extensions to the UNI. However, the switch must support the following:

￿

￿

Registering the same ATM address on multiple ports

Registering multiple ATM addresses on a single port

If the switch does not support these features, load balancing and failover is automati- cally disabled.

Dell PowerVault 7x0N Systems — Connecting to ATM and FDDI Networks 15