Dell 7x0N manual $%&$%

Page 2

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, notices, cautions, and warnings, and they are used as follows:

NOTE: A NOTE indicates important information that helps you make better use of your computer system.

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿ ￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿!￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿"￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿"￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿#￿￿￿￿

$￿%￿￿￿&￿￿￿￿$￿%￿￿￿&￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿!￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿"￿

￿￿￿￿￿￿￿￿￿￿￿￿￿￿"￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿#￿￿￿￿

____________________

Information in this document is subject to change without notice. © 1999 Dell Computer Corporation. All rights reserved.

Reproduction in any manner whatsoever without the written permission of Dell Computer Corpo- ration is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, and PowerVault are trademarks of Dell Computer Corporation.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Computer Corporation disclaims any propri- etary interest in trademarks and trade names other than its own.

September 1999 P/N 65CNP Rev. A00

Image 2
Contents Page $%&$% Iii Duplex Fiber Optic Cable Connecting to an ATM Card Page Page #!$!%$ #!%#!$ Page To start the configuration, perform the following steps $## Page #$#%$$$$$$&$ +,*--./ #$0$1$22$$2$%$1%$ #$0$1$22$$2$%$1%$2 Page 2424+4 Page $$#!$ +$##$*!# %=%=*2DC,+ ######+ /etc/hosts file #$!%&$ Hostname #/* .+$ +$ #0Page FDDI-TP Two duplex Fddi Port B Fiber optic cables Port a Pin Function Bypasspresent Return grounded internallyAdconfig device SynopsisCluster Considerations Adinfo -c device Framing Output CellsInput Cells Hdr-CRCPay-CRC CS-PDUsCSProto SARProtoOptions Atmarp -f Atmarp -N hostname Atmarp -N -aAtmarp -d hostname See Also Atmconfig device Atmconfig -q peak off device Show DeleteNaarp1 Add Set -lecs Wait