Dell 7x0N manual

Page 25

To display information about all the current FORE/IP PVCs, type the following command:

￿￿2￿￿+￿￿￿

A display similar to the following appears:

￿￿2￿￿+￿￿￿

iface=a5 switch.port=f21a2420.56 vpi.vci=0.114 aal=5 encapsulation=NULL

iface=a5 switch.port=f21a2420.25 vpi.vci=0.113 aal=5 encapsulation=NULL

￿￿!￿￿￿￿￿￿￿￿/* ￿.￿￿￿￿+$

You can delete outgoing and incoming FORE/IP PVCs.

To delete an outgoing FORE/IP PVC entry, type the following command: ￿￿2￿￿+￿￿￿￿￿￿￿￿￿￿￿￿

hostname is the name or IP address of the remote host.

To delete an incoming FORE/IP PVC for a remote host, use the following command: ￿￿2￿￿+￿￿A￿￿￿￿￿￿￿￿￿￿￿￿￿￿

iface is the name of the interface

vpi and vci have the values of the VPI and VCI of the FORE/IP PVC to be deleted for the specified interface.

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

You can connect the filer to one of three available FDDI network configurations.

Table 3 describes the three FDDI configurations you can use, and Table 4 lists the FDDI cabling requirements:

￿￿￿￿￿￿ ￿￿￿￿￿￿!￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿￿

￿￿￿￿￿￿￿￿￿￿￿￿￿

 

 

 

Single-attached FDDI Fiber or

Dual-attached

Dual-attached

FDDI-TP card*

FDDI fiber card

FDDI fiber card

*Do not exceed the maximum cable length specifications in the appropriate FDDI American National Standards Institute (ANSI) standard.

Dell PowerVault 7x0N Systems — Connecting to ATM and FDDI Networks

21

Image 25
Contents Page $%&$% Iii Duplex Fiber Optic Cable Connecting to an ATM Card Page Page #!% #!$!%$#!$ Page To start the configuration, perform the following steps $## Page #$#%$$$$$$&$ +,*--./ #$0$1$22$$2$%$1%$ #$0$1$22$$2$%$1%$2 Page 2424+4 Page +$## $$#!$$*!# %=%=*2DC,+ ######+ /etc/hosts file #$!%&$ Hostname +$ #0 #/* .+$Page FDDI-TP Two duplex Fddi Port B Fiber optic cables Port a Bypasspresent Return grounded internally Pin FunctionSynopsis Adconfig deviceCluster Considerations Adinfo -c device Input Cells Output CellsFraming Hdr-CRCCSProto CS-PDUsPay-CRC SARProtoOptions Atmarp -d hostname Atmarp -N hostname Atmarp -N -aAtmarp -f See Also Atmconfig device Atmconfig -q peak off device Delete ShowNaarp1 Add Wait Set -lecs