Ryobi SSP0501 manuel dutilisation Troubleshooting, Problem Cause Possible Solution

Page 11

TROUBLESHOOTING

PROBLEM

CAUSE

POSSIBLE SOLUTION

Motor does not run.

Sprayer is not plugged in.

Make sure unit is plugged in.

 

Breaker is tripped.

Reset breaker.

 

 

 

Motor overheats.

Piston has seized up.

Thoroughly clean the sprayer using long-

 

 

term storage cleaning instructions in the

 

 

Maintenance section of this manual.

 

Extension cord is too long.

Use only the size extension cord recom-

 

 

mended previously in this manual.

 

Continuous spray operation.

Release trigger at the end of each pass to

 

 

allow the motor to cool.

 

 

 

Motor has a low hum but does not

Piston has seized up.

Thoroughly clean the sprayer using long-

spray.

 

term storage cleaning instructions in the

 

 

Maintenance section of this manual.

 

 

 

Motor seems to be running properly

Suction tube and filter are loose or

Reinstall or replace suction tube and filter

but doesn’t spray.

damaged.

as needed.

 

Atomizer valve is clogged or worn out.

Clean or replace atomizer valve.

 

Material being sprayed is too thick.

Follow material manufacturer’s directions

 

 

and thin material as needed.

 

Plugged spray tip or intake filter;

Thoroughly clean the sprayer and, if

 

worn piston.

necessary, replace piston*, using storage

 

 

cleaning instructions in the Maintenance

 

 

section of this manual.

 

 

 

Sprayed material is spitting or glob-

Paint container volume is getting low.

Refill paint container.

bing up.

Material being sprayed is too thick.

Follow material manufacturer’s directions

 

 

 

to thin material as needed.

 

Suction tube is loose.

Reinstall suction tube securely.

 

Atomizer valve is clogged or worn out.

Clean or replace atomizer valve.

 

Worn spray tip or piston.

Clean or replace spray tip or piston*.

 

Material being sprayed has been

Allow paint to sit for approximately 1 hour.

 

shaken and has air pockets

 

 

 

 

Paint/stain spray overspray is exces-

Spray tip is too far from the surface

Hold sprayer closer to the surface being

sive.

being sprayed.

sprayed.

 

 

 

Paint/stain runs or sags on the work

Proper paint methods not being ob-

Refer to Operating the Sprayer earlier in

surface.

served.

this manual.

 

 

 

Paint/stain is leaking behind the spray

Spray tip is loose.

Tighten spray tip.

tip.

Atomizer valve is worn or not posi-

Replace or reposition atomizer valve as

 

 

tioned properly.

needed.

 

 

 

Unit will not prime

Atomizer valve is worn

Replace the atomizer valve

 

 

 

Small bead in spray pattern

Moving the sprayer too fast

Slow arm speed down

 

 

 

*Although unlikely, a worn piston is possible. A replacement piston can be purchased by calling customer service at 1-800-525-2579. Follow the instructions in Cleaning the Sprayer for Storage to access the piston for replacement.

NOTE: FIGURES (ILLUSTRATIONS) START ON PAGE 12

AFTER FRENCH AND SPANISH LANGUAGE SECTIONS.

11 — English

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Save this Manual for Future Reference OPERATOR’S ManualIntroduction WarrantyRead ALL Instructions Important Safety InstructionsSpecific Safety Rules Name DESIGNATION/EXPLANATION SymbolsCalifornia Proposition Grounding Instructions ElectricalExtension Cords Electrical ConnectionAssembly FeaturesOperating the Sprayer OperationApplications Filling Sprayer with PAINT/STAINTo clean the sprayer for short term storage Cleaning the Sprayer After USEReplacing the Atomizer Valve Assembly MaintenanceGeneral Maintenance Cleaning the Sprayer for StorageRefer to Operating the Sprayer earlier TroubleshootingProblem Cause Possible Solution Arrière Table DES MatièresGarantie Lire Toutes LES Instructions Instructions Importantes Concernant LA SécuritéAVERTISSEMENT  Savoir arrêter la machine rapidement Règles DE Sécurité ParticulièresProposition 65 DE LA Californie AVERTISSEMENT  SymbolesSymbole Signal Signification Instructions DE Mise À LA Terre Caractéristiques ÉlectriquesCordons Prolongateurs Connexion ÉlectriqueAssemblage CaractéristiquesUtilisation DU Pistolet UtilisationAvertissement AVERTISSEMENT  Remplir LE Pistolet DE Peinture OU DE TeintureAvertissement EntretienEntretien Général Nettoyage DU Pistolet Après UtilisationVoir les figures 8 9, Remplacement DE L’ENSEMBLE Valve DE PulvérisateurPour procéder au remplacement Nettoyage DU Pistolet AUX Fins D’ENTREPOSAGEDépannage Problème Cause Solution PossibleFrançais Pág. posterior Índice DE ContenidoIntroducción GarantíaLEA Todas LAS Instrucciones Instrucciones DE Seguridad ImportantesAdvertencia Reglas DE Seguridad Específicas California Propuesta DE LEY NÚM SímbolosPeligro PrecauciónInstrucciones DE Conexión a Tierra Aspectos EléctricosCordones DE Extensión Conexión EléctricaArmado CaracterísticasFuncionamiento DEL Rociador FuncionamientoUsos Llenado DEL Rociador CON PINTURA/ TinteMantenimiento General MantenimientoPrecaución Limpieza DEL Rociador Después DE UtilizarloVea la figura 10, página Limpieza DEL Rociador Para GuardarloReemplazo DEL Conjunto DE Válvula Atomizadora Vea las figuras 8 9, páginaProblema Causa Posible Solución Corrección DE ProblemasGrounding pin broche de terre, patilla de conexión a tierra Place Line of Lubricant on Piston Shaft Page OPERATOR’S Manual / Power Paint Sprayer Tool

SSP0501 specifications

The Ryobi SSP0501 is a powerful and versatile multi-tool that caters to both DIY enthusiasts and professional tradespeople. This innovative tool excels in a variety of applications, making it a must-have in any workshop or home garage.

One of the standout features of the Ryobi SSP0501 is its robust motor, which delivers consistent power for efficient performance. The tool's design emphasizes ease of use, with ergonomic handles that offer a comfortable grip, reducing user fatigue during extended projects. The lightweight design further enhances maneuverability, allowing users to tackle intricate tasks without straining.

The SSP0501 is equipped with a range of attachments that enable it to function as a sander, grinder, and cutter. This versatility makes it suitable for a broad spectrum of materials including wood, metal, and plastics. The quick-release attachment system simplifies the process of switching between tools, ensuring that users can seamlessly adapt to various tasks without wasting valuable time.

Additionally, the Ryobi SSP0501 incorporates advanced technology to enhance its performance. The variable speed control allows users to adjust the tool's speed according to the specific requirements of the job at hand. This feature not only improves precision but also extends the lifespan of the attachments by minimizing wear and tear.

Safety is a paramount concern in all Ryobi products, and the SSP0501 is no exception. It includes built-in safety features such as an adjustable guard to shield users from debris and a lock-on switch for continuous operation, reducing the risk of accidental activation.

Battery performance is another crucial aspect of the SSP0501. It boasts a long-lasting battery life, and when paired with Ryobi's One+ system, users can interchange batteries across multiple tools, maximizing efficiency and convenience. The LED work light enhances visibility in dimly lit areas, providing added functionality during use.

In summary, the Ryobi SSP0501 stands out due to its durable construction, powerful motor, and a plethora of attachments that make it an exceptional choice for various projects. Its user-friendly design, adjustable speed control, and safety features further elevate its usability. Whether for household repairs or professional tasks, the SSP0501 is a formidable tool that combines power and versatility, ensuring it meets the demands of any user. This multi-tool is a valuable investment for those seeking practicality and efficiency in their work.
Top Page Image Contents