Ryobi SSP0501 Cleaning the Sprayer After USE, To clean the sprayer for short term storage

Page 9

OPERATION

To create an even coating over the entire surface:

•Move your arm at a steady rate of speed and make sure to move your entire arm, not just your wrist.

•Keep the sprayer an even distance from the area being sprayed, which should be between 8 to 10 inches from the tip of the sprayer to the surface being sprayed.

•Depress the trigger to begin the spray off the material you want to paint. Operate the sprayer in straight horizontal or vertical strokes across the surface being painted, then release the trigger off the material to end the stroke.

NOTE: For spray quality consistency when using thinner paints, it may be necessary to keep the trigger depressed between strokes.

When finished, unplug the sprayer, return any unused paint or stain to its original container, and thoroughly clean the sprayer.

CAUTION:

It is important to thoroughly clean the sprayer after each use or when changing colors. Allowing paint or stain to remain in an idle tool for an extended period can cause its moving pieces to seize up.

WARNING:

Do not clean with any flammable liquids such as paint stripper, paint remover, brush cleaner, mineral spirits, lacquer thinner, turpentine, acetone, gasoline, kerosene, etc.

CLEANING THE SPRAYER AFTER USE

The solution used to clean the sprayer is determined by the type of material that has been sprayed. For anything other than latex material, follow the material manufacturer’s directions for appropriate clean-up.

To clean the sprayer for short term storage:

Unplug the sprayer.

If you haven’t already done so, remove the paint container and return any unused paint or stain to its original container.

Fill the paint container with lukewarm water (for water based paints) or non-flammable solvent (for oil-based paints or varnish, or any other non-flammable paint thinner (following the use of oil-based products).

Reinstall the paint container.

Plug in the sprayer.

Spray the solution onto a piece of cardboard or other scrap material. Continue spraying until all the solution is used.

Unplug the sprayer.

Place a line of lubricant on the piston. To gain access to the piston, follow the instructions in Cleaning the Sprayer for Storage in the Maintenance section of this manual.

Use a damp cloth to wipe the exterior of the sprayer. The unit is now ready to put away.

9 — English

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Save this Manual for Future Reference OPERATOR’S ManualIntroduction WarrantyRead ALL Instructions Important Safety InstructionsSpecific Safety Rules Symbols California PropositionName DESIGNATION/EXPLANATION Extension Cords ElectricalElectrical Connection Grounding InstructionsAssembly FeaturesApplications OperationFilling Sprayer with PAINT/STAIN Operating the SprayerTo clean the sprayer for short term storage Cleaning the Sprayer After USEGeneral Maintenance MaintenanceCleaning the Sprayer for Storage Replacing the Atomizer Valve AssemblyTroubleshooting Problem Cause Possible SolutionRefer to Operating the Sprayer earlier Table DES Matières GarantieArrière Instructions Importantes Concernant LA Sécurité AVERTISSEMENT Lire Toutes LES Instructions Savoir arrêter la machine rapidement Règles DE Sécurité ParticulièresSymboles Symbole Signal SignificationProposition 65 DE LA Californie AVERTISSEMENT  Cordons Prolongateurs Caractéristiques ÉlectriquesConnexion Électrique Instructions DE Mise À LA TerreAssemblage CaractéristiquesAvertissement AVERTISSEMENT  UtilisationRemplir LE Pistolet DE Peinture OU DE Teinture Utilisation DU PistoletEntretien Général EntretienNettoyage DU Pistolet Après Utilisation AvertissementPour procéder au remplacement Remplacement DE L’ENSEMBLE Valve DE PulvérisateurNettoyage DU Pistolet AUX Fins D’ENTREPOSAGE Voir les figures 8 9,Dépannage Problème Cause Solution PossibleFrançais Introducción Índice DE ContenidoGarantía Pág. posteriorInstrucciones DE Seguridad Importantes AdvertenciaLEA Todas LAS Instrucciones Reglas DE Seguridad Específicas Peligro SímbolosPrecaución California Propuesta DE LEY NÚMCordones DE Extensión Aspectos EléctricosConexión Eléctrica Instrucciones DE Conexión a TierraArmado CaracterísticasUsos FuncionamientoLlenado DEL Rociador CON PINTURA/ Tinte Funcionamiento DEL RociadorPrecaución MantenimientoLimpieza DEL Rociador Después DE Utilizarlo Mantenimiento GeneralReemplazo DEL Conjunto DE Válvula Atomizadora Limpieza DEL Rociador Para GuardarloVea las figuras 8 9, página Vea la figura 10, páginaProblema Causa Posible Solución Corrección DE ProblemasGrounding pin broche de terre, patilla de conexión a tierra Place Line of Lubricant on Piston Shaft Page OPERATOR’S Manual / Power Paint Sprayer Tool

SSP0501 specifications

The Ryobi SSP0501 is a powerful and versatile multi-tool that caters to both DIY enthusiasts and professional tradespeople. This innovative tool excels in a variety of applications, making it a must-have in any workshop or home garage.

One of the standout features of the Ryobi SSP0501 is its robust motor, which delivers consistent power for efficient performance. The tool's design emphasizes ease of use, with ergonomic handles that offer a comfortable grip, reducing user fatigue during extended projects. The lightweight design further enhances maneuverability, allowing users to tackle intricate tasks without straining.

The SSP0501 is equipped with a range of attachments that enable it to function as a sander, grinder, and cutter. This versatility makes it suitable for a broad spectrum of materials including wood, metal, and plastics. The quick-release attachment system simplifies the process of switching between tools, ensuring that users can seamlessly adapt to various tasks without wasting valuable time.

Additionally, the Ryobi SSP0501 incorporates advanced technology to enhance its performance. The variable speed control allows users to adjust the tool's speed according to the specific requirements of the job at hand. This feature not only improves precision but also extends the lifespan of the attachments by minimizing wear and tear.

Safety is a paramount concern in all Ryobi products, and the SSP0501 is no exception. It includes built-in safety features such as an adjustable guard to shield users from debris and a lock-on switch for continuous operation, reducing the risk of accidental activation.

Battery performance is another crucial aspect of the SSP0501. It boasts a long-lasting battery life, and when paired with Ryobi's One+ system, users can interchange batteries across multiple tools, maximizing efficiency and convenience. The LED work light enhances visibility in dimly lit areas, providing added functionality during use.

In summary, the Ryobi SSP0501 stands out due to its durable construction, powerful motor, and a plethora of attachments that make it an exceptional choice for various projects. Its user-friendly design, adjustable speed control, and safety features further elevate its usability. Whether for household repairs or professional tasks, the SSP0501 is a formidable tool that combines power and versatility, ensuring it meets the demands of any user. This multi-tool is a valuable investment for those seeking practicality and efficiency in their work.
Top Page Image Contents