Ryobi P204 manuel dutilisation Removing Bits, Drilling, Wood DRILLING, Metal DRILLING

Page 9

OPERATION

removing BITS

See Figure 8, page 12.

Lock the switch trigger by placing the direction of rotation selector in the center position.

Open the chuck jaws.

Note: Rotate the chuck body in the direction of the arrow marked UNLOCK to open the chuck jaws. Do not use a wrench to tighten or loosen the chuck jaws.

Remove the drill bit.

DRILLING

See Figure 10, page 12.

A level is located on the top of the motor housing to help keep the drill bit level during use.

Check the direction of rotation selector for the correct setting (forward or reverse).

Secure the material to be drilled in a vise or with clamps to keep it from turning as the drill bit rotates.

Hold the drill firmly and place the bit at the point to be drilled.

Depress the switch trigger to start the drill.

Move the drill bit into the workpiece, applying only enough pressure to keep the bit cutting. Do not force the drill or apply side pressure to elongate a hole. Let the tool do the work.

WARNING:

Be prepared for binding at bit breakthrough. When these situations occur, drill has a tendency to grab and kick opposite to the direction of rotation and could cause loss of control when breaking through material. If not prepared, this loss of control can result in possible serious injury.

When drilling hard, smooth surfaces, use a center punch to mark the desired hole location. This will prevent the drill bit from slipping off-center as the hole is started.

When drilling metals, use a light oil on the drill bit to keep it from overheating. The oil will prolong the life of the bit and increase the drilling action.

If the bit jams in the workpiece or if the drill stalls, stop the tool immediately. Remove the bit from the workpiece and determine the reason for jamming.

NOTE: This drill has an electric brake. When the switch trigger is released, the chuck stops turning. When the brake is functioning properly, sparks will be visible through the vent slots on the housing. This is normal and is the action of the brake.

WOOD DRILLING

For maximum performance, use high speed steel bits for wood drilling.

Begin drilling at a very low speed to prevent the bit from slipping off the starting point. Increase the speed as the drill bit bites into the material.

When drilling through holes, place a block of wood behind the workpiece to prevent ragged or splintered edges on the back side of the hole.

METAL DRILLING

For maximum performance, use high speed steel bits for metal or steel drilling.

Begin drilling at a very low speed to prevent the bit from slipping off the starting point.

Maintain a speed and pressure which allows cutting without overheating the bit. Applying too much pressure will:

Overheat the drill;

Wear the bearings;

Bend or burn bits; and

Produce off-center or irregular-shaped holes.

When drilling large holes in metal, start with a small bit, then finish with a larger bit. Also, lubricate the bit with oil to improve drilling action and increase bit life.

9 – English

Image 9
Contents Accepts ALL 18 Volt one+ Battery Packs Save this Manual for Future ReferenceBatteries and chargers sold Separately Introduction Table of ContentsWork Area Safety General Safety RulesElectrical Safety Personal SafetySpecific Safety Rules Battery Tool USE and CareService Symbols Symbol Signal MeaningName DESIGNATION/EXPLANATION Assembly FeaturesOperation ADJUSTing Torque Adjustable torque clutchInstalling Bits TWO-SPEED Gear Train hi-loDrilling Removing BitsWood DRILLING Metal DRILLINGGeneral Maintenance MaintenanceBattery Pack Removal and Preparation For Recycling Chuck RemovalGarantie AVERTISSEMENT  Règles DE Sécurité GénéralesRègles DE Sécurité Particulières Utilisation ET Entretien DE LA BatterieDépannage Symbole Signal Signification SymbolesSymbole NOM Désignation / Explication Aura pour conséquences des blessures graves ou mortellesAssemblage CaractéristiquesUtilisation Installation DU Bloc-piles Caractéristiques Relatives À LA Protection DES Piles Retrait DU Bloc-pilesEmbrayage DE Couple Réglable Installation DES EmboutsRéglage DU Couple Rangement D’EMBOUTPerçage Retrait DES EmboutsPerçage DU Bois Perçage DU MétalRetrait ET Préparation DU Piles Pour LE Recyclage EntretienEntretien Général Retrait DU MandrinIntroducción Índice DE ContenidoAdvertencia Reglas DE Seguridad GeneralesSeguridad Eléctrica Seguridad PersonalEmpleo Y Cuidado DE LA Herramienta DE BateríaS Reglas DE Seguridad EspecíficasServicio ¡ADVERTENCIAPeligro SímbolosAdvertencia PrecauciónArmado CaracterísticasAplicaciones FuncionamientoCaracterísticas DE Protección DE LAS Baterías Para Instalar EL Paquete DE BateríaSGatillo DEL Interruptor DE Velocidad Variable Gatillo DEL InterruptorEmbrague de fuerza de torsión ajustable Ajuste de la fuerza de torsiónRemoción DE LAS Brocas Instalación DE LAS BrocasTaladrado Taladrado EN MaderaMantenimiento General MantenimientoDesmontaje DEL Portabrocas Para Apretar EL Portabrocas Cuando SE AflojePage Wrong / InCorrect Forma incorrecta Right / Correct / Forma CorrectaPage ONE World TECHNOLOGIES, INC OPERATOR’S Manual / 18 vOLT DRILL-DRIVER

P204 specifications

The Ryobi P204 is a versatile and reliable tool that is designed to meet the demands of both DIY enthusiasts and professional tradespeople. As part of Ryobi's ONE+ system, this compact drill/driver features a powerful and efficient motor that delivers exceptional performance in a variety of applications.

One of the main features of the Ryobi P204 is its 18-volt lithium-ion battery compatibility, which offers extended run time and consistent power. This battery technology enables users to take advantage of a wide range of Ryobi's ONE+ tools, allowing for a seamless transition between tasks without the need for multiple battery types.

The P204 is equipped with an efficient 2-speed gear system, allowing users to select between a high-speed setting for drilling into softer materials and a lower speed setting for driving screws or working with harder materials. This versatility makes it suitable for both heavy-duty construction projects and lighter home improvement tasks.

Another important characteristic of the Ryobi P204 is its adjustable clutch with 24 torque settings. This feature provides precise control over the amount of force applied when driving screws, reducing the risk of damaging materials and ensuring a secure fit.

Additionally, the drill/driver includes a keyless chuck that allows for quick and easy bit changes. This user-friendly design minimizes downtime and enhances productivity, making it an essential tool for both casual users and professionals.

The P204 also features an integrated LED light, which illuminates the work area and allows for increased visibility in dimly lit spaces, ensuring accuracy and precision in every project.

For added convenience, the tool is lightweight and ergonomically designed, reducing fatigue during extended use and making it easy to maneuver in tight spaces.

Overall, the Ryobi P204 combines power, versatility, and comfort in a compact design, making it a favored choice for many users. Its efficient battery system, adjustable torque options, and user-friendly features equip it to tackle a wide range of tasks with ease and precision, cementing its reputation as a dependable addition to any tool collection.