Ryobi BT3100-1 manual Operators Manual, Save this Manual for Future Reference

Page 1

OPERATOR'S MANUAL

10 in. (254 mm) TABLE SAW BT3100-1

Your new Table Saw has been engineered and manufactured to Ryobi's high standards for dependability, ease of operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the operator's manual.

Thank you for buying a Ryobi Table Saw.

SAVE THIS MANUAL FOR FUTURE REFERENCE

Image 1

Contents Save this Manual for Future Reference Operators ManualProduct Specifications Table of ContentsRules for Safe Operation Symbol MeaningRead ALL Instructions Blades Coast After Turn OFF Before Making a CUT, be Sure ALL Adjustments are SecureSafety and International Symbols Extension Cords ElectricalElectrical Connection Grounding InstructionsGlossary of Terms Tools Needed UnpackingIn. NUT Driver Socket WrenchKey Description Quan Loose Parts ListE J Following items are included with your table saw leg standGetting to Know Your SAW FeaturesSliding ScaleOperating Components Power SwitchBlades Speed and WiringAssembling LEG Stand AssemblyAssembling Storage Brackets To Install Front and Back RailsMounting the LEG Stand on the Table SAW Base Rear Rail END Plug Holder NUT Miter To Install Miter Table and FenceHandwheel Hole BREMOVING/REPLACING the Throat Plate To Install Accessory Table and RIP FenceLever FIT LIP of Table Into Rear RailTo Install Blade Guard Assembly To Check SAW Blade InstallationSmall HEX Wrench Throat PlateReplacing the Throat Plate Screws Operation Types of Cuts HOW to Mount a Featherboard HOW to Make a FeatherboardFeatherboard To Remove the Blade Lever Right Rotate Blade AdjustingLocking Lever Left Riving Knife Blade Blade Guard Riving KnifeInch Riving Knife Mounting PlateTo Adjust the Blade Angle To Adjust the Blade DepthTo SET the Scale to the Blade Never use rip fence as cutoff gauge when crosscutting Adjustingmiter Clampfence Quick StopTo Lock Miter Table To Make a Straight Cross CUTTo Make a Miter CUT Adjusting ClampTo Make a Straight RIP CUT Miter Table Blade Rear Rail RIP FenceTo Make a Bevel RIP CUT To Make a Bevel Cross CUTTo Make a Compound Miter CUT Accessory Miter Locking Clamps Rail ClampTo Make a Large Panel CUT Featherboard To Make NON-THROUGH CutsClamp Push Block Bevel Operation General Maintenance MaintenanceBackup Washer LubricationTo Check the Alignment of the RIP Fence to the Blade To SET Blade AT 0 orScrews Lock NUT Stop Bolt LockTo Align the Miter Locking Clamps To Adjust the Bevel Locking LeverSET Screw Lobe Socket Head Screw HEX NUT TAB CAM Spring Screw SET Front Rail Miter Locking ClampTo Adjust the Accessory Table To Adjust the Front and Rear Rail ClampsTo Adjust the Sliding Miter Table Assembly Spring Plate Backup HEX NUTTo Check Miter Base Parallelism Checking Sliding Miter Table AssemblyEight screws are visible on the miter base B Making Adjustments to Sliding Miter Table AssemblyTo Adjust QUICK-STOP To Adjust the Miter FenceMiter Indicator LIP of BaseProblem Cause Solution Trouble ShootingCenter Ryobi Authorized ServicePage 112 107 8283 108 113 101 110 104 122 Refer to Figure111 102 105 117 116 114 115 See Back page for Ordering Instructions Parts List FigureParts List Contd Sliding Miter Table Assembly RIP Fence Assembly Motor Assembly 506 500 501 504 502 503 505 Key Description Quan Blade Guard AssemblyRyobi 10 in mm Table SAW Model NO. BT3100-1 KEY Description Quan Parts List for FigureRyobi TECHNOLOGIES, INC Operators Manual 10 in mm Table Saw Model BT3100-1