Ryobi BT3100-1 manual To Adjust the Miter Fence, To Adjust QUICK-STOP, LIP of Base, Slide

Page 39

MAINTENANCE

WARNING:

Begin by unplugging your saw. Failure to unplug saw could result in accidental starting causing possible serious injury.

TO ADJUST THE MITER FENCE

■Set the miter fence (H) at 0° as shown in figure 53. Miter indicator (I) should be set precisely on 0° and secured in place with adjusting clamp (J).

■There are four slides located under the sliding miter table. These slides let the miter table move on the base. Three slides are mounted on eccentric screws that can be adjusted by loosening the hex nuts on top of the miter table. See Figure 55.

■Loosen the rear hex nuts (Q) on top of sliding miter table for this adjustment procedure.

Note: The front screws (R) are only needed to remove excessive play in the slides due to wear from extended use. They are not needed for this procedure. The right front hex nut is a non-eccentric pivot and should never be loosened.

■Adjust the right rear eccentric screw from the lower side of the miter table so that maximum play exists between the slide and miter base.

■Push left rear of miter table snugly against miter base as shown by the arrow (S) in figure 56 and secure.

■Place a framing square firmly against the miter fence, with the other side against the blade.

■Adjust left rear screw from underneath miter table until miter fence and blade are square with each other.

■Tighten hex nut securely.

■Adjust right rear screw from underneath miter table to remove excessive play.

■Tighten hex nut securely.

■Recheck your setups carefully. Also make sure all screws, hex nuts, etc. have been tightened securely.

■If sliding miter table assembly is still not square with the blade, repeat the above procedures as needed.

■Make sure that slides remain square to miter base edge to prevent “cocking” which will result in excessive play in miter table.

TO ADJUST QUICK-STOP

The quick-stop is preset at the factory to stop the miter fence at exactly 0° . However, when sliding miter table adjustments are made, these adjustments may cause the quick stop to need adjusting. Check quick-stop with miter scale set at 0° . If adjustments are needed, proceed with the following steps:

■Loosen the eccentric screw holding the quick-stop.

■Place the quick-stop against the miter fence with miter scale set at 0° . See Figure 57.

■Adjust eccentric screw until it holds quick-stop securely against miter fence.

■Retighten hex nut, securing eccentric screw and quick- stop.

■Check your work. If the quick-stop is not at 0° , repeat above steps.

HEX NUT

MITER TABLE

 

ECCENTRIC

 

LIP OF BASE

SLIDE

 

SCREW

Fig. 55

 

 

 

R

H

SQ

Fig. 56

MITER INDICATOR

MITER FENCE

ADJUSTING

ZEROCLAMP DEGREES

MITER

FENCE

QUICK STOP AND

ECCENTRIC SCREW

Fig. 57

Page 39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Save this Manual for Future Reference Operators ManualProduct Specifications Table of ContentsRules for Safe Operation Symbol MeaningRead ALL Instructions Blades Coast After Turn OFF Before Making a CUT, be Sure ALL Adjustments are SecureSafety and International Symbols Grounding Instructions ElectricalExtension Cords Electrical ConnectionGlossary of Terms Socket Wrench UnpackingTools Needed In. NUT DriverKey Description Quan Loose Parts ListE J Following items are included with your table saw leg standScale FeaturesGetting to Know Your SAW SlidingOperating Components Power SwitchBlades Speed and WiringAssembling LEG Stand AssemblyTo Install Front and Back Rails Assembling Storage BracketsMounting the LEG Stand on the Table SAW Base Hole B To Install Miter Table and FenceRear Rail END Plug Holder NUT Miter HandwheelFIT LIP of Table Into Rear Rail To Install Accessory Table and RIP FenceREMOVING/REPLACING the Throat Plate LeverThroat Plate To Check SAW Blade InstallationTo Install Blade Guard Assembly Small HEX WrenchReplacing the Throat Plate Screws Operation Types of Cuts HOW to Make a Featherboard HOW to Mount a FeatherboardFeatherboard Lever Right Rotate Blade Adjusting To Remove the BladeLocking Lever Left Riving Knife Mounting Plate Blade Guard Riving KnifeRiving Knife Blade InchTo Adjust the Blade Depth To Adjust the Blade AngleTo SET the Scale to the Blade To Make a Straight Cross CUT Adjustingmiter Clampfence Quick StopNever use rip fence as cutoff gauge when crosscutting To Lock Miter TableMiter Table Blade Rear Rail RIP Fence Adjusting ClampTo Make a Miter CUT To Make a Straight RIP CUTTo Make a Bevel RIP CUT To Make a Bevel Cross CUTAccessory Miter Locking Clamps Rail Clamp To Make a Compound Miter CUTTo Make a Large Panel CUT To Make NON-THROUGH Cuts FeatherboardClamp Push Block Bevel Operation Lubrication MaintenanceGeneral Maintenance Backup WasherStop Bolt Lock To SET Blade AT 0 orTo Check the Alignment of the RIP Fence to the Blade Screws Lock NUTScrew SET Front Rail Miter Locking Clamp To Adjust the Bevel Locking LeverTo Align the Miter Locking Clamps SET Screw Lobe Socket Head Screw HEX NUT TAB CAM SpringSpring Plate Backup HEX NUT To Adjust the Front and Rear Rail ClampsTo Adjust the Accessory Table To Adjust the Sliding Miter Table AssemblyTo Check Miter Base Parallelism Checking Sliding Miter Table AssemblyEight screws are visible on the miter base B Making Adjustments to Sliding Miter Table AssemblyLIP of Base To Adjust the Miter FenceTo Adjust QUICK-STOP Miter IndicatorProblem Cause Solution Trouble ShootingCenter Ryobi Authorized ServicePage Refer to Figure 112 107 8283 108 113 101 110 104 122111 102 105 117 116 114 115 See Back page for Ordering Instructions Parts List FigureParts List Contd Sliding Miter Table Assembly RIP Fence Assembly Motor Assembly 506 500 501 504 502 503 505 Key Description Quan Blade Guard AssemblyRyobi 10 in mm Table SAW Model NO. BT3100-1 KEY Description Quan Parts List for FigureRyobi TECHNOLOGIES, INC Operators Manual 10 in mm Table Saw Model BT3100-1
Top Page Image Contents