Ryobi BT3100-1 manual Blade Guard Assembly, 506 500 501 504 502 503 505 Key Description Quan

Page 49

RYOBI 10 in. (254 mm) TABLE SAW - MODEL NO. BT3100-1

FIGURE 62: BLADE GUARD ASSEMBLY

8

5

7

6

5

4

3

2

11

	5
9	12

5

2

1

3

10

Key		1	Key
No.	Description	Quan.	No.	Description	Quan.

1	Screw and Washer	2
2	Anti-Kickback Fingers	2
3	Spacer Cap	2
4	Torsion Spring	1
5	Push Nut	4
6	Dowel Pin	1

7	Arm	1
8	Cover	1
9	Dowel Pin	1
10	Riving Knife Assembly	1
11	Warning Label	1
12	Hand Warning Label	1

FIGURE 63: REPLACEMENT PARTS

506

		500
		501	504
			504
		502
		503
				505
Key				Key
No.	Description		Quan.	No.	Description	Quan.

500	3/32 in. Hex Key	1
501	1/8 in. Hex Key	1
502	5/32 in. Hex Key	1
503	3/16 in. Hex Key	1

504	Large Wrench	1
505	Small Wrench	1
506	Saw Blade	1

Page 49

Image 49

Contents Save this Manual for Future Reference Operators ManualProduct Specifications Table of ContentsRules for Safe Operation Symbol MeaningRead ALL Instructions Blades Coast After Turn OFF Before Making a CUT, be Sure ALL Adjustments are SecureSafety and International Symbols Extension Cords ElectricalElectrical Connection Grounding InstructionsGlossary of Terms Tools Needed UnpackingIn. NUT Driver Socket WrenchKey Description Quan Loose Parts ListE J Following items are included with your table saw leg standGetting to Know Your SAW FeaturesSliding ScaleOperating Components Power SwitchBlades Speed and WiringAssembling LEG Stand AssemblyAssembling Storage Brackets To Install Front and Back RailsMounting the LEG Stand on the Table SAW Base Rear Rail END Plug Holder NUT Miter To Install Miter Table and FenceHandwheel Hole BREMOVING/REPLACING the Throat Plate To Install Accessory Table and RIP FenceLever FIT LIP of Table Into Rear RailTo Install Blade Guard Assembly To Check SAW Blade InstallationSmall HEX Wrench Throat PlateReplacing the Throat Plate Screws Operation Types of Cuts HOW to Mount a Featherboard HOW to Make a FeatherboardFeatherboard To Remove the Blade Lever Right Rotate Blade AdjustingLocking Lever Left Riving Knife Blade Blade Guard Riving KnifeInch Riving Knife Mounting PlateTo Adjust the Blade Angle To Adjust the Blade DepthTo SET the Scale to the Blade Never use rip fence as cutoff gauge when crosscutting Adjustingmiter Clampfence Quick StopTo Lock Miter Table To Make a Straight Cross CUTTo Make a Miter CUT Adjusting ClampTo Make a Straight RIP CUT Miter Table Blade Rear Rail RIP FenceTo Make a Bevel RIP CUT To Make a Bevel Cross CUTTo Make a Compound Miter CUT Accessory Miter Locking Clamps Rail ClampTo Make a Large Panel CUT Featherboard To Make NON-THROUGH CutsClamp Push Block Bevel Operation General Maintenance MaintenanceBackup Washer LubricationTo Check the Alignment of the RIP Fence to the Blade To SET Blade AT 0 orScrews Lock NUT Stop Bolt LockTo Align the Miter Locking Clamps To Adjust the Bevel Locking LeverSET Screw Lobe Socket Head Screw HEX NUT TAB CAM Spring Screw SET Front Rail Miter Locking ClampTo Adjust the Accessory Table To Adjust the Front and Rear Rail ClampsTo Adjust the Sliding Miter Table Assembly Spring Plate Backup HEX NUTTo Check Miter Base Parallelism Checking Sliding Miter Table AssemblyEight screws are visible on the miter base B Making Adjustments to Sliding Miter Table AssemblyTo Adjust QUICK-STOP To Adjust the Miter FenceMiter Indicator LIP of BaseProblem Cause Solution Trouble ShootingCenter Ryobi Authorized ServicePage 112 107 8283 108 113 101 110 104 122 Refer to Figure111 102 105 117 116 114 115 See Back page for Ordering Instructions Parts List FigureParts List Contd Sliding Miter Table Assembly RIP Fence Assembly Motor Assembly 506 500 501 504 502 503 505 Key Description Quan Blade Guard AssemblyRyobi 10 in mm Table SAW Model NO. BT3100-1 KEY Description Quan Parts List for FigureRyobi TECHNOLOGIES, INC Operators Manual 10 in mm Table Saw Model BT3100-1