Ryobi BT3100-1 manual Trouble Shooting, Problem Cause Solution

Page 40

TROUBLE SHOOTING

PROBLEM

CAUSE

SOLUTION

Excess vibration.

Blade is out of balance.

Replace blade.

 

Blade is damaged.

Replace blade.

 

Saw is not mounted securely.

Tighten all hardware.

 

Work surface is uneven.

Reposition on flat surface.

 

 

Adjust legs of table saw stand.

 

Blade is warped

Check Saw Blade Installation on

 

 

page 20. Replace blade if neces-

 

 

sary.

 

 

 

Rip fence does not move smoothly.

Rip fence not mounted correctly.

Remount the rip fence.

 

Rails are dirty or sticky.

Clean and wax rails.

 

Clamp screw is out of adjustment.

Adjust clamp screw counterclockwise.

 

See page 34.

 

 

 

 

Rip fence does not lock at rear.

Clamp screw is out of adjustment.

Adjust clamp screw clockwise.

See page 34.

 

Cutting binds or burns work.

Blade is dull.

Replace or sharpen blade

 

 

Blade is heeling.

Align miter base.

 

 

Work is fed too fast.

Slow the feed rate.

 

 

Rip fence is misaligned.

Align the rip fence.

 

 

Riving knife is misaligned.

Adjust the riving knife with shims

 

 

 

provided.

 

 

Wood is warped.

Replace the wood. Always cut with

 

 

 

convex side to table surface.

 

 

 

 

Wood edges away from rip fence

Rip fence is misaligned.

Check and adjust the rip fence.

when ripping.

 

 

 

 

Blade not properly sharpened or set. Sharpen or set blade.

Sliding miter table assembly does not move smoothly.

Miter base or slides improperly adjusted.

See page 36 for Adjustments to Sliding Miter Table Assembly .

Page 40

Image 40
Contents Operators Manual Save this Manual for Future ReferenceTable of Contents Product SpecificationsSymbol Meaning Rules for Safe OperationRead ALL Instructions Before Making a CUT, be Sure ALL Adjustments are Secure Blades Coast After Turn OFFSafety and International Symbols Electrical Extension CordsElectrical Connection Grounding InstructionsGlossary of Terms Unpacking Tools NeededIn. NUT Driver Socket WrenchLoose Parts List Key Description QuanFollowing items are included with your table saw leg stand E JFeatures Getting to Know Your SAWSliding ScalePower Switch Operating ComponentsSpeed and Wiring BladesAssembly Assembling LEG StandAssembling Storage Brackets To Install Front and Back RailsMounting the LEG Stand on the Table SAW Base To Install Miter Table and Fence Rear Rail END Plug Holder NUT MiterHandwheel Hole BTo Install Accessory Table and RIP Fence REMOVING/REPLACING the Throat PlateLever FIT LIP of Table Into Rear RailTo Check SAW Blade Installation To Install Blade Guard AssemblySmall HEX Wrench Throat PlateReplacing the Throat Plate Screws Operation Types of Cuts HOW to Mount a Featherboard HOW to Make a FeatherboardFeatherboard To Remove the Blade Lever Right Rotate Blade AdjustingLocking Lever Left Blade Guard Riving Knife Riving Knife BladeInch Riving Knife Mounting PlateTo Adjust the Blade Angle To Adjust the Blade DepthTo SET the Scale to the Blade Adjustingmiter Clampfence Quick Stop Never use rip fence as cutoff gauge when crosscuttingTo Lock Miter Table To Make a Straight Cross CUTAdjusting Clamp To Make a Miter CUTTo Make a Straight RIP CUT Miter Table Blade Rear Rail RIP FenceTo Make a Bevel Cross CUT To Make a Bevel RIP CUTTo Make a Compound Miter CUT Accessory Miter Locking Clamps Rail ClampTo Make a Large Panel CUT Featherboard To Make NON-THROUGH CutsClamp Push Block Bevel Operation Maintenance General MaintenanceBackup Washer LubricationTo SET Blade AT 0 or To Check the Alignment of the RIP Fence to the BladeScrews Lock NUT Stop Bolt LockTo Adjust the Bevel Locking Lever To Align the Miter Locking ClampsSET Screw Lobe Socket Head Screw HEX NUT TAB CAM Spring Screw SET Front Rail Miter Locking ClampTo Adjust the Front and Rear Rail Clamps To Adjust the Accessory TableTo Adjust the Sliding Miter Table Assembly Spring Plate Backup HEX NUTChecking Sliding Miter Table Assembly To Check Miter Base ParallelismMaking Adjustments to Sliding Miter Table Assembly Eight screws are visible on the miter base BTo Adjust the Miter Fence To Adjust QUICK-STOPMiter Indicator LIP of BaseTrouble Shooting Problem Cause SolutionRyobi Authorized Service CenterPage 112 107 8283 108 113 101 110 104 122 Refer to Figure111 102 105 117 116 114 115 Parts List Figure See Back page for Ordering InstructionsParts List Contd Sliding Miter Table Assembly RIP Fence Assembly Motor Assembly Blade Guard Assembly 506 500 501 504 502 503 505 Key Description QuanRyobi 10 in mm Table SAW Model NO. BT3100-1 Parts List for Figure KEY Description QuanOperators Manual 10 in mm Table Saw Model BT3100-1 Ryobi TECHNOLOGIES, INC