Ryobi BT3100-1 manual Assembling Storage Brackets, Mounting the LEG Stand on the Table SAW Base

Page 16

ASSEMBLY

ASSEMBLING STORAGE BRACKETS

See Figure 9.

Take storage brackets from loose parts.

Take the following hardware from the leg stand hardware bag:

4 screws (1/4-20 x 1/2 in. Pan Hd.)

4 hex nuts (1/4-20)

4 washers (1/4 in.)

Secure storage brackets to upper braces of leg stand as shown in figures 8 and 9.

MOUNTING THE LEG STAND ON THE TABLE SAW BASE

See Figure 10.

Take the following from a small hardware bag:

4 hex bolts (1/4-20 x 3/4 in.)

4 hex nuts (1/4-20)

8 flat washers (1/4 in.)

Note: This hardware was in the bag with hardware for assembling the leg stand and leveling feet.

WARNING:

Do not lift the saw without help. The saw base weighs approximately 75 lbs. Hold it close to your body. Keep your knees bent and lift with your legs, not your back. Ignoring these precautions can result in back injury.

Place the leg stand on the table saw base. Align the holes in the table with the holes in the end braces.

Place a flat washer on a bolt and insert through hole. Add a flat washer and a hex nut. Hand tighten. See Figure 10.

Repeat for three remaining holes. Tighten all hardware with a wrench. You may find it helpful to use one wrench to hold the head of the bolt and one to tighten the hex nut.

STORAGE BRACKET(S)

UPPER BRACE

LOWER BRACE

LEG

LEG STAND ASSEMBLED

Fig. 9

WARNING:

Do not connect to power supply until assembly is complete. Failure to comply could result in accidental starting and possible serious injury.

TO INSTALL FRONT AND BACK RAILS

See Figures 11 and 12.

Position end plugs on both rails and secure in place by tapping with a block of wood or a rubber mallet.

Loosen the front rail clamps one half turn from the tightened position. Loosen the square rail holder nut one-fourth (1/4) turn to allow the front rail to slide over it. See Figures 11 and 12.

Mount the front rail with the scale facing the outside toward the operator.

SAW BASE

FLAT

WASHER

LEG STAND

HEX NUT

HEX BOLT

Fig. 10

Page 16

Image 16
Contents Operators Manual Save this Manual for Future ReferenceTable of Contents Product SpecificationsSymbol Meaning Rules for Safe OperationRead ALL Instructions Before Making a CUT, be Sure ALL Adjustments are Secure Blades Coast After Turn OFFSafety and International Symbols Electrical Extension CordsElectrical Connection Grounding InstructionsGlossary of Terms Unpacking Tools NeededIn. NUT Driver Socket WrenchLoose Parts List Key Description QuanFollowing items are included with your table saw leg stand E JFeatures Getting to Know Your SAWSliding ScalePower Switch Operating ComponentsSpeed and Wiring BladesAssembly Assembling LEG StandAssembling Storage Brackets To Install Front and Back RailsMounting the LEG Stand on the Table SAW Base To Install Miter Table and Fence Rear Rail END Plug Holder NUT MiterHandwheel Hole BTo Install Accessory Table and RIP Fence REMOVING/REPLACING the Throat PlateLever FIT LIP of Table Into Rear RailTo Check SAW Blade Installation To Install Blade Guard AssemblySmall HEX Wrench Throat PlateReplacing the Throat Plate Screws Operation Types of Cuts HOW to Mount a Featherboard HOW to Make a FeatherboardFeatherboard To Remove the Blade Lever Right Rotate Blade AdjustingLocking Lever Left Blade Guard Riving Knife Riving Knife BladeInch Riving Knife Mounting PlateTo Adjust the Blade Angle To Adjust the Blade DepthTo SET the Scale to the Blade Adjustingmiter Clampfence Quick Stop Never use rip fence as cutoff gauge when crosscuttingTo Lock Miter Table To Make a Straight Cross CUTAdjusting Clamp To Make a Miter CUTTo Make a Straight RIP CUT Miter Table Blade Rear Rail RIP FenceTo Make a Bevel Cross CUT To Make a Bevel RIP CUTTo Make a Compound Miter CUT Accessory Miter Locking Clamps Rail ClampTo Make a Large Panel CUT Featherboard To Make NON-THROUGH CutsClamp Push Block Bevel Operation Maintenance General MaintenanceBackup Washer LubricationTo SET Blade AT 0 or To Check the Alignment of the RIP Fence to the BladeScrews Lock NUT Stop Bolt LockTo Adjust the Bevel Locking Lever To Align the Miter Locking ClampsSET Screw Lobe Socket Head Screw HEX NUT TAB CAM Spring Screw SET Front Rail Miter Locking ClampTo Adjust the Front and Rear Rail Clamps To Adjust the Accessory TableTo Adjust the Sliding Miter Table Assembly Spring Plate Backup HEX NUTChecking Sliding Miter Table Assembly To Check Miter Base ParallelismMaking Adjustments to Sliding Miter Table Assembly Eight screws are visible on the miter base BTo Adjust the Miter Fence To Adjust QUICK-STOPMiter Indicator LIP of BaseTrouble Shooting Problem Cause SolutionRyobi Authorized Service CenterPage 112 107 8283 108 113 101 110 104 122 Refer to Figure111 102 105 117 116 114 115 Parts List Figure See Back page for Ordering InstructionsParts List Contd Sliding Miter Table Assembly RIP Fence Assembly Motor Assembly Blade Guard Assembly 506 500 501 504 502 503 505 Key Description QuanRyobi 10 in mm Table SAW Model NO. BT3100-1 Parts List for Figure KEY Description QuanOperators Manual 10 in mm Table Saw Model BT3100-1 Ryobi TECHNOLOGIES, INC