Ryobi BT3100-1 manual Replacing the Throat Plate Screws

Page 20

ASSEMBLY

Blade alignment with the riving knife can be adjusted for different blade widths. Refer to Settings and Adjustments in the Operations Section. Before continuing, read To

Check, Replace or Adjust the Riving Knife and Blade Guard Assembly on page 25 to make sure of proper riving knife alignment.

Check the blade guard assembly for clearances and free movement. Reinstall the throat plate into the opening, lower the blade and secure the attachment screw. Tighten the screw securely.

REPLACING THE THROAT PLATE

THROAT PLATE

SCREWS

Fig. 20

Page 20

Image 20
Contents Operators Manual Save this Manual for Future ReferenceTable of Contents Product SpecificationsSymbol Meaning Rules for Safe OperationRead ALL Instructions Before Making a CUT, be Sure ALL Adjustments are Secure Blades Coast After Turn OFFSafety and International Symbols Electrical Extension CordsElectrical Connection Grounding InstructionsGlossary of Terms Unpacking Tools NeededIn. NUT Driver Socket WrenchLoose Parts List Key Description QuanFollowing items are included with your table saw leg stand E JFeatures Getting to Know Your SAWSliding ScalePower Switch Operating ComponentsSpeed and Wiring BladesAssembly Assembling LEG StandMounting the LEG Stand on the Table SAW Base To Install Front and Back RailsAssembling Storage Brackets To Install Miter Table and Fence Rear Rail END Plug Holder NUT MiterHandwheel Hole BTo Install Accessory Table and RIP Fence REMOVING/REPLACING the Throat PlateLever FIT LIP of Table Into Rear RailTo Check SAW Blade Installation To Install Blade Guard AssemblySmall HEX Wrench Throat PlateReplacing the Throat Plate Screws Operation Types of Cuts Featherboard HOW to Make a FeatherboardHOW to Mount a Featherboard Locking Lever Left Lever Right Rotate Blade AdjustingTo Remove the Blade Blade Guard Riving Knife Riving Knife BladeInch Riving Knife Mounting PlateTo SET the Scale to the Blade To Adjust the Blade DepthTo Adjust the Blade Angle Adjustingmiter Clampfence Quick Stop Never use rip fence as cutoff gauge when crosscuttingTo Lock Miter Table To Make a Straight Cross CUTAdjusting Clamp To Make a Miter CUTTo Make a Straight RIP CUT Miter Table Blade Rear Rail RIP FenceTo Make a Bevel Cross CUT To Make a Bevel RIP CUTTo Make a Large Panel CUT Accessory Miter Locking Clamps Rail ClampTo Make a Compound Miter CUT Clamp Push Block Bevel To Make NON-THROUGH CutsFeatherboard Operation Maintenance General MaintenanceBackup Washer LubricationTo SET Blade AT 0 or To Check the Alignment of the RIP Fence to the BladeScrews Lock NUT Stop Bolt LockTo Adjust the Bevel Locking Lever To Align the Miter Locking ClampsSET Screw Lobe Socket Head Screw HEX NUT TAB CAM Spring Screw SET Front Rail Miter Locking ClampTo Adjust the Front and Rear Rail Clamps To Adjust the Accessory TableTo Adjust the Sliding Miter Table Assembly Spring Plate Backup HEX NUTChecking Sliding Miter Table Assembly To Check Miter Base ParallelismMaking Adjustments to Sliding Miter Table Assembly Eight screws are visible on the miter base BTo Adjust the Miter Fence To Adjust QUICK-STOPMiter Indicator LIP of BaseTrouble Shooting Problem Cause SolutionRyobi Authorized Service CenterPage 111 102 105 117 116 114 115 Refer to Figure112 107 8283 108 113 101 110 104 122 Parts List Figure See Back page for Ordering InstructionsParts List Contd Sliding Miter Table Assembly RIP Fence Assembly Motor Assembly Blade Guard Assembly 506 500 501 504 502 503 505 Key Description QuanRyobi 10 in mm Table SAW Model NO. BT3100-1 Parts List for Figure KEY Description QuanOperators Manual 10 in mm Table Saw Model BT3100-1 Ryobi TECHNOLOGIES, INC