Ryobi BT3100-1 manual Parts List for Figure, KEY Description Quan

Page 51

Page 51

RYOBI 10 in. (254 mm) TABLE SAW – MODEL NO. BT3100-1

The model number will be found on the data plate attached to the right side panel of the cabinet, next to the saw’s on board receptacle. Always mention the model number in all correspondence regarding your TABLE SAW or when ordering repair parts.

 

 

PARTS LIST FOR FIGURE 64

KEY

 

 

NO.

DESCRIPTION

QUAN.

1

Leveling Foot

4

2

Hex Nut

32

3

Washer

32

4

Carriage Bolt

24

5

Leg

4

6

Upper Brace

2

7

Screw

4

8

Hex Nut

8

9

Upper Side Brace

2

10

Lower Leg Brace

4

11

Storage Bracket

4

12

Washer

12

13

Bolt

4

 

Stand Fastener Package

1

 

Operator’s Manual

 

Page 50 Page 52
Image 51
Page 50 Page 52
Contents Save this Manual for Future Reference Operators ManualProduct Specifications Table of ContentsRules for Safe Operation Symbol MeaningRead ALL Instructions Blades Coast After Turn OFF Before Making a CUT, be Sure ALL Adjustments are SecureSafety and International Symbols Grounding Instructions ElectricalExtension Cords Electrical ConnectionGlossary of Terms Socket Wrench UnpackingTools Needed In. NUT DriverKey Description Quan Loose Parts ListE J Following items are included with your table saw leg standScale FeaturesGetting to Know Your SAW SlidingOperating Components Power SwitchBlades Speed and WiringAssembling LEG Stand AssemblyTo Install Front and Back Rails Assembling Storage BracketsMounting the LEG Stand on the Table SAW Base Hole B To Install Miter Table and FenceRear Rail END Plug Holder NUT Miter HandwheelFIT LIP of Table Into Rear Rail To Install Accessory Table and RIP FenceREMOVING/REPLACING the Throat Plate LeverThroat Plate To Check SAW Blade InstallationTo Install Blade Guard Assembly Small HEX WrenchReplacing the Throat Plate Screws Operation Types of Cuts HOW to Make a Featherboard HOW to Mount a FeatherboardFeatherboard Lever Right Rotate Blade Adjusting To Remove the BladeLocking Lever Left Riving Knife Mounting Plate Blade Guard Riving KnifeRiving Knife Blade InchTo Adjust the Blade Depth To Adjust the Blade AngleTo SET the Scale to the Blade To Make a Straight Cross CUT Adjustingmiter Clampfence Quick StopNever use rip fence as cutoff gauge when crosscutting To Lock Miter TableMiter Table Blade Rear Rail RIP Fence Adjusting ClampTo Make a Miter CUT To Make a Straight RIP CUTTo Make a Bevel RIP CUT To Make a Bevel Cross CUTAccessory Miter Locking Clamps Rail Clamp To Make a Compound Miter CUTTo Make a Large Panel CUT To Make NON-THROUGH Cuts FeatherboardClamp Push Block Bevel Operation Lubrication MaintenanceGeneral Maintenance Backup WasherStop Bolt Lock To SET Blade AT 0 orTo Check the Alignment of the RIP Fence to the Blade Screws Lock NUTScrew SET Front Rail Miter Locking Clamp To Adjust the Bevel Locking LeverTo Align the Miter Locking Clamps SET Screw Lobe Socket Head Screw HEX NUT TAB CAM SpringSpring Plate Backup HEX NUT To Adjust the Front and Rear Rail ClampsTo Adjust the Accessory Table To Adjust the Sliding Miter Table AssemblyTo Check Miter Base Parallelism Checking Sliding Miter Table AssemblyEight screws are visible on the miter base B Making Adjustments to Sliding Miter Table AssemblyLIP of Base To Adjust the Miter FenceTo Adjust QUICK-STOP Miter IndicatorProblem Cause Solution Trouble ShootingCenter Ryobi Authorized ServicePage Refer to Figure 112 107 8283 108 113 101 110 104 122111 102 105 117 116 114 115 See Back page for Ordering Instructions Parts List FigureParts List Contd Sliding Miter Table Assembly RIP Fence Assembly Motor Assembly 506 500 501 504 502 503 505 Key Description Quan Blade Guard AssemblyRyobi 10 in mm Table SAW Model NO. BT3100-1 KEY Description Quan Parts List for FigureRyobi TECHNOLOGIES, INC Operators Manual 10 in mm Table Saw Model BT3100-1
Top Page Image Contents