Ryobi BT3100-1 manual Assembly, Assembling LEG Stand

Page 15

ASSEMBLY

Assembly is best done in the area where the saw will be used. When you remove the table saw base, loose parts, and hardware from the packing materials, check all items with the loose parts list and drawing. If you are unsure about the description of any part, refer to the drawing. If any parts are missing, delay assembling until you have obtained the missing part(s).

ASSEMBLING LEG STAND

See Figures 8 and 9.

■Take the following hardware from the leg stand hardware bag:

24 carriage bolts (5/16-18 x 3/4 in.)

4 leveling feet

32 flat washers (5/16 in.)

32 hex nuts (5/16-18)

Note: Remaining hardware from this bag is used for mount- ing leg stand on the table saw base and mounting storage brackets to upper brace.

■Take 4 legs and 8 braces from loose parts.

■Place an upper side brace inside two of the legs, with the legs wide end up. (Upper side braces have two large holes in each end.) Make sure the two posts on the leg align with the small holes on the brace.

UPPER BRACE

■Align the two large holes on the brace and the legs. Insert the carriage bolts. Add flat washers and hex nuts and hand tighten. Repeat for the other upper brace. These are the front and back sets.

■For the side sets, install a upper brace on two legs. Add hardware and finger tighten. Repeat for the other upper brace.

■Use the same steps to install the lower braces. Tighten all hex nuts with a wrench.

■Place a hex nut and flat washer on each leveling foot. Install the leveling feet from the bottom of each leg with the bolts pointing up. Cap with the remaining flat washers and hex nuts but do not tighten.

■Move the leg set to desired location. Adjust the leveling feet with a wrench, then tighten the top hex nut.

BOLT

HEX NUT

WASHER

CARRIAGE	UPPER	WASHER
CARRIAGE	SIDE BRACE
BOLT		HEX
		NUT
WASHER

LEG

HEX NUT

HEX NUT

SCREW

	STORAGE	LOWER BRACE
	BRACKET(S)	LOWER BRACE
	BRACKET(S)

WASHER

HEX NUT

LEVELING FOOT

Fig. 8

Page 15

Image 15

Contents Save this Manual for Future Reference Operators ManualProduct Specifications Table of ContentsRules for Safe Operation Symbol MeaningRead ALL Instructions Blades Coast After Turn OFF Before Making a CUT, be Sure ALL Adjustments are SecureSafety and International Symbols Grounding Instructions ElectricalExtension Cords Electrical ConnectionGlossary of Terms Socket Wrench UnpackingTools Needed In. NUT DriverKey Description Quan Loose Parts ListE J Following items are included with your table saw leg standScale FeaturesGetting to Know Your SAW SlidingOperating Components Power SwitchBlades Speed and WiringAssembling LEG Stand AssemblyTo Install Front and Back Rails Assembling Storage BracketsMounting the LEG Stand on the Table SAW Base Hole B To Install Miter Table and FenceRear Rail END Plug Holder NUT Miter HandwheelFIT LIP of Table Into Rear Rail To Install Accessory Table and RIP FenceREMOVING/REPLACING the Throat Plate LeverThroat Plate To Check SAW Blade InstallationTo Install Blade Guard Assembly Small HEX WrenchReplacing the Throat Plate Screws Operation Types of Cuts HOW to Make a Featherboard HOW to Mount a FeatherboardFeatherboard Lever Right Rotate Blade Adjusting To Remove the BladeLocking Lever Left Riving Knife Mounting Plate Blade Guard Riving KnifeRiving Knife Blade InchTo Adjust the Blade Depth To Adjust the Blade AngleTo SET the Scale to the Blade To Make a Straight Cross CUT Adjustingmiter Clampfence Quick StopNever use rip fence as cutoff gauge when crosscutting To Lock Miter TableMiter Table Blade Rear Rail RIP Fence Adjusting ClampTo Make a Miter CUT To Make a Straight RIP CUTTo Make a Bevel RIP CUT To Make a Bevel Cross CUTAccessory Miter Locking Clamps Rail Clamp To Make a Compound Miter CUTTo Make a Large Panel CUT To Make NON-THROUGH Cuts FeatherboardClamp Push Block Bevel Operation Lubrication MaintenanceGeneral Maintenance Backup WasherStop Bolt Lock To SET Blade AT 0 orTo Check the Alignment of the RIP Fence to the Blade Screws Lock NUTScrew SET Front Rail Miter Locking Clamp To Adjust the Bevel Locking LeverTo Align the Miter Locking Clamps SET Screw Lobe Socket Head Screw HEX NUT TAB CAM SpringSpring Plate Backup HEX NUT To Adjust the Front and Rear Rail ClampsTo Adjust the Accessory Table To Adjust the Sliding Miter Table AssemblyTo Check Miter Base Parallelism Checking Sliding Miter Table AssemblyEight screws are visible on the miter base B Making Adjustments to Sliding Miter Table AssemblyLIP of Base To Adjust the Miter FenceTo Adjust QUICK-STOP Miter IndicatorProblem Cause Solution Trouble ShootingCenter Ryobi Authorized ServicePage Refer to Figure 112 107 8283 108 113 101 110 104 122111 102 105 117 116 114 115 See Back page for Ordering Instructions Parts List FigureParts List Contd Sliding Miter Table Assembly RIP Fence Assembly Motor Assembly 506 500 501 504 502 503 505 Key Description Quan Blade Guard AssemblyRyobi 10 in mm Table SAW Model NO. BT3100-1 KEY Description Quan Parts List for FigureRyobi TECHNOLOGIES, INC Operators Manual 10 in mm Table Saw Model BT3100-1