Grizzly G0689 owner manual Table of Contents

Page 3

Table of Contents

INTRODUCTION	2
Manual Accuracy	2
Contact Info	2
Functional Overview	2
Identification	3
SECTION 1: SAFETY	6
Safety Instructions for Machinery	6
Additional Safety Instructions for Planers	8
SECTION 2: CIRCUIT REQUIREMENTS	9
110V Operation	9
SECTION 3: SETUP	10
Setup Safety	10
Unpacking	10
Inventory	10
Clean Up	11
Site Considerations	11
Assembly	12
Test Run	12
Mounting	13
SECTION 4: OPERATIONS	14
Operation Safety	14
Basic Controls	14
ON/OFF Switch	15
Reset Button	15
Depth-of-Cut	16
Elevation Lock	17
Basic Operations	18
Planing Tips	18
Wood Characteristics	19
Wood Types	20

SECTION 5: ACCESSORIES	21
SECTION 6: MAINTENANCE	23
Schedule	23
Cleaning	23
Lubrication	23
SECTION 7: SERVICE	24
Troubleshooting	24
Knife Replacement	25
Motor	27
Drive Belt	28
Impeller Belt	29
Feed Rollers	29
Extension Wing/Table Alignment	30
Elevation Lock Adjustment	30
Thickness Stop Calibration	31
Wiring Diagram	32
SECTION 8: PARTS	33
Main Parts Breakdown	33
Main Parts List	34
Base Parts Breakdown	36
Warning Labels Breakdown and List	38
WARRANTY AND RETURNS	41

Image 3

Contents Model G0689 Planer with BUILT-IN Dust Collection Ss ,EAD from Leadbased PAINTS Table of Contents Introduction Manual Accuracy Functional OverviewContact Info Identification G0689 13 Planer Machine Data SheetModel G0689 !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29 !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4 !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29# 53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 53%3 2%#/--%.$%$- !##%33/2%3 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2Unplugging during adjustments Additional Safety Instructions for Planers110V Operation Circuit RequirementsUnpacking SetupSetup Safety InventoryWorkbench Load Clean UpPlacement Location Site ConsiderationsAssembly Test Run To attach the elevation crank assemblyTo test run the machine Mounting Example of a direct mount setup G0689 13 PlanerOperations Operation Safety Basic ControlsReset Button ON/OFF SwitchElevation Crank Depth-of-CutTo use the thickness stop Elevation LockThickness Stop Cutterhead Elevation ScaleStep Basic OperationsPlaning Tips To use the planerWood Characteristics Type Wood TypesG7313-700 lb Capacity Shop FOX Stand AccessoriesT20803-13 Replacement Knives T20448T20452 T20501 T20456 H0736G8983 G8985 G8984 G8983-Tilting Roller StandG8984-Single Roller Stand G8985-5 Roller StandLubrication MaintenanceCleaning ScheduleTroubleshooting ServiceKnife Replacement Tools Needed QtyTo remove the knives To inspect the cutterhead, gib, and knives Motor To install the knivesTo replace the belt Drive BeltPerform Steps 2-3 from Drive Belt on To clean the feed rollersImpeller Belt Feed RollersExtension Wing/ Table Alignment Elevation Lock AdjustmentIf adjustment is necessary, proceed as fol- lows To adjust the elevation lockThickness Stop Calibration To adjust the thickness stopSwitch wiring G0689 13 Planer Wiring DiagramMain Parts Breakdown PartsDescription Main Parts ListGear Large 70T Base Parts Breakdown Base Parts List 302 301 303 304 307 305 306 308 309 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7! Warranty and Returns #ALL 4ODAYD&ORO! &2%%