Grizzly owner manual Mounting, Example of a direct mount setup G0689 13 Planer

Page 15

5.Turn the machine OFF.

6.Remove the switch disabling key, as shown in Figure 8.

Figure 8. Removing switch key from paddle

switch.

7.Try to start the machine with the paddle switch.

—If the machine does not start, the switch disabling feature is working as designed.

—If the machine starts, immediately stop the machine. The switch disabling feature is not working correctly. This safety feature must work properly before proceeding with regular operations. Call Tech Support for help.

Mounting

Once you have confirmed that your machine is running properly, you may choose to mount it to a workbench through the holes in the base.

The strongest mounting option is a "Through Mount" where holes are drilled all the way through the workbench, and hex bolts, washers, and hex nuts are used to secure the planer to the workbench.

7dai

;aViLVh]Zg

-ACHINEH"ASE

7ORKBENCH

;aViLVh]Zg

AdX`LVh]Zg

=ZmCji

Figure 9. Example of a through mount setup.

Another option for mounting is a "Direct Mount" where the machine is simply secured to the work- bench with a lag screw.

AV\HXgZl

;aViLVh]Zg

-ACHINEH"ASE

7ORKBENCH

Figure 10. Example of a direct mount setup.

G0689 13" Planer

-13-

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Model G0689 Planer with BUILT-IN Dust Collection Ss ,EAD from Leadbased PAINTS Table of Contents Introduction Manual Accuracy Functional OverviewContact Info Identification G0689 13 Planer Machine Data SheetModel G0689  !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29  !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4 !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#  53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 53%3 2%#/--%.$%$- !##%33/2%3  -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2Unplugging during adjustments Additional Safety Instructions for Planers110V Operation Circuit RequirementsUnpacking SetupSetup Safety InventoryWorkbench Load Clean UpPlacement Location Site ConsiderationsAssembly Test Run To attach the elevation crank assemblyTo test run the machine Mounting Example of a direct mount setup G0689 13 PlanerOperations Operation Safety Basic ControlsReset Button ON/OFF SwitchElevation Crank Depth-of-CutTo use the thickness stop Elevation LockThickness Stop Cutterhead Elevation ScaleStep Basic OperationsPlaning Tips To use the planerWood Characteristics Type Wood TypesG7313-700 lb Capacity Shop FOX Stand AccessoriesT20803-13 Replacement Knives T20448T20452 T20501 T20456 H0736G8983 G8985 G8984 G8983-Tilting Roller StandG8984-Single Roller Stand G8985-5 Roller StandLubrication MaintenanceCleaning ScheduleTroubleshooting ServiceKnife Replacement Tools Needed QtyTo remove the knives To inspect the cutterhead, gib, and knives Motor To install the knivesTo replace the belt Drive BeltPerform Steps 2-3 from Drive Belt on To clean the feed rollersImpeller Belt Feed RollersExtension Wing/ Table Alignment Elevation Lock AdjustmentIf adjustment is necessary, proceed as fol- lows To adjust the elevation lockThickness Stop Calibration To adjust the thickness stopSwitch wiring G0689 13 Planer Wiring DiagramMain Parts Breakdown PartsDescription Main Parts ListGear Large 70T Base Parts Breakdown Base Parts List 302 301 303 304 307 305 306 308 309 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7!  Warranty and Returns #ALL 4ODAYD&ORO! &2%%
Top Page Image Contents