Grizzly G0689 owner manual Drive Belt, To replace the belt

Page 30

Drive Belt

The cutterhead is driven by a belt that is located on the right-hand side of the motor and cutterhead assembly (when facing the front of the machine). The belt is very durable, but with extended use may begin to slip, indicating the need for replace- ment.

Tools Needed	Qty
Hex Wrench 4mm	1
Hex Wrench 5mm	1
Hex Wrench 6mm	1
To replace the belt:

1.DISCONNECT PLANER FROM POWER!

2.Remove the elevation crank and the four button head cap screws that secure the top cover. Remove the top plate (Figure 35).

Elevation Crank

Top Plate

Thickness Stop Knob

Figure 35. Top and side cover removal.

3.Remove the thickness stop knob by pulling outward on it, then lift and pull the right side cover off.

4.Remove the belt guard shown in Figure 36 by removing the cap screws that secure it.

Belt Guard

Figure 36. Belt guard.

5.Loosen the motor mount bolt, shown in Figure 37, to release tension on the belt.

	Drive Belt	Impeller Belt
		Impeller Belt
	Motor Mount Bolt	Cutterhead
	Motor Mount Bolt	Pulley Assembly
		Pulley Assembly

Figure 37. Cutterhead drive components.

6.Remove the impeller belt by rolling it off the cutterhead pulley assembly, then remove the drive belt.

7.Place the new drive belt over both pulleys. Lift the motor by hand using moderate force to apply tension to the belt, then tighten the motor mount bolt.

8.Replace the impeller belt, belt guard, side and top covers, thickness stop knob, button head cap screws, and cutterhead elevation crank in the reverse order from which they were removed.

-28-	G0689 13" Planer

Image 30

Contents Model G0689 Planer with BUILT-IN Dust Collection Ss ,EAD from Leadbased PAINTS Table of Contents Introduction Manual Accuracy Functional OverviewContact Info Identification Machine Data Sheet G0689 13 PlanerModel G0689 !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4 !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2 53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 53%3 2%#/--%.$%$- !##%33/2%3 !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#Additional Safety Instructions for Planers Unplugging during adjustmentsCircuit Requirements 110V OperationInventory SetupSetup Safety UnpackingSite Considerations Clean UpPlacement Location Workbench LoadAssembly Test Run To attach the elevation crank assemblyTo test run the machine Example of a direct mount setup G0689 13 Planer MountingOperation Safety Basic Controls OperationsON/OFF Switch Reset ButtonDepth-of-Cut Elevation CrankCutterhead Elevation Scale Elevation LockThickness Stop To use the thickness stopTo use the planer Basic OperationsPlaning Tips StepWood Characteristics Wood Types TypeT20448T20452 T20501 T20456 H0736 AccessoriesT20803-13 Replacement Knives G7313-700 lb Capacity Shop FOX StandG8985-5 Roller Stand G8983-Tilting Roller StandG8984-Single Roller Stand G8983 G8985 G8984Schedule MaintenanceCleaning LubricationService TroubleshootingKnife Replacement Tools Needed QtyTo remove the knives To inspect the cutterhead, gib, and knives To install the knives MotorDrive Belt To replace the beltFeed Rollers To clean the feed rollersImpeller Belt Perform Steps 2-3 from Drive Belt onTo adjust the elevation lock Elevation Lock AdjustmentIf adjustment is necessary, proceed as fol- lows Extension Wing/ Table AlignmentTo adjust the thickness stop Thickness Stop CalibrationWiring Diagram Switch wiring G0689 13 PlanerParts Main Parts BreakdownMain Parts List DescriptionGear Large 70T Base Parts Breakdown Base Parts List 302 301 303 304 307 305 306 308 309 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7! Warranty and Returns #ALL 4ODAYD&ORO! &2%%