Grizzly G0689 owner manual Introduction, Manual Accuracy Functional Overview, Contact Info

Page 4

INTRODUCTION

Manual Accuracy

Functional Overview

 

 

 

 

 

 

We are proud to offer this manual with your new machine! We've made every effort to be exact with the instructions, specifications, drawings, and photographs of the machine we used when writ- ing this manual. However, sometimes errors do happen and we apologize for them.

Also, owing to our policy of continuous improve- ment, your machine may not exactly match the manual. If you find this to be the case, and the difference between the manual and machine leaves you in doubt, immediately call our techni- cal support for updates or clarification.

For your convenience, we always keep current Grizzly manuals and most updates available on our website at www.grizzly.com. Any updates to your machine will be reflected in these documents as soon as they are complete. Visit our site often to check for the latest updates!

Contact Info

We stand behind our machines. If you have any service questions, parts requests or general ques- tions about the machine, please call or write us at the location listed below.

Grizzly Industrial, Inc.

1203 Lycoming Mall Circle

Muncy, PA 17756

Phone: (570) 546-9663

Fax: (800) 438-5901

E-Mail: techsupport@grizzly.com

If you have any comments regarding this manual, please write to us at the address below:

Grizzly Industrial, Inc.

C/O Technical Documentation Manager

P.O. Box 2069

Bellingham, WA 98227-2069

Email: manuals@grizzly.com

-2-

The Model G0689 Planer allows the user to plane material from the surface of boards in precise increments. The depth-of-cut is adjusted with the cutterhead elevation crank and is measured by the cutterhead elevation scale or the depth-of-cut gauge. One turn of the crank raises or lowers the cutterhead 1⁄16".

Once the depth-of-cut is adjusted, the operator feeds the board into the infeed roller which pulls the board into the cutterhead, where material is removed. The outfeed roller then pulls the board away from the cutterhead. After the board is completely free from the outfeed roller, it can be returned to the infeed side of the machine. Larger workpieces can be passed across the return roll- ers on top of the machine.

The depth-of-cut is again adjusted, and the pro- cess is continued until the desired board thick- ness is reached.

G0689 13" Planer

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Model G0689 Planer with BUILT-IN Dust Collection Ss ,EAD from Leadbased PAINTS Table of Contents Manual Accuracy Functional Overview IntroductionContact Info Identification Machine Data Sheet G0689 13 PlanerModel G0689  !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4  !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29 53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2  53%3 2%#/--%.$%$- !##%33/2%3 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2  !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#Additional Safety Instructions for Planers Unplugging during adjustmentsCircuit Requirements 110V OperationSetup Setup SafetyInventory UnpackingClean Up Placement LocationSite Considerations Workbench LoadTo attach the elevation crank assembly Assembly Test RunTo test run the machine Example of a direct mount setup G0689 13 Planer MountingOperation Safety Basic Controls OperationsON/OFF Switch Reset ButtonDepth-of-Cut Elevation CrankElevation Lock Thickness StopCutterhead Elevation Scale To use the thickness stopBasic Operations Planing TipsTo use the planer StepWood Characteristics Wood Types TypeAccessories T20803-13 Replacement KnivesT20448T20452 T20501 T20456 H0736 G7313-700 lb Capacity Shop FOX StandG8983-Tilting Roller Stand G8984-Single Roller StandG8985-5 Roller Stand G8983 G8985 G8984Maintenance CleaningSchedule LubricationService TroubleshootingTools Needed Qty Knife ReplacementTo remove the knives To inspect the cutterhead, gib, and knives To install the knives MotorDrive Belt To replace the beltTo clean the feed rollers Impeller BeltFeed Rollers Perform Steps 2-3 from Drive Belt onElevation Lock Adjustment If adjustment is necessary, proceed as fol- lowsTo adjust the elevation lock Extension Wing/ Table AlignmentTo adjust the thickness stop Thickness Stop CalibrationWiring Diagram Switch wiring G0689 13 PlanerParts Main Parts BreakdownMain Parts List DescriptionGear Large 70T Base Parts Breakdown Base Parts List 302 301 303 304 307 305 306 308 309 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7!  Warranty and Returns #ALL 4ODAYD&ORO! &2%%
Top Page Image Contents