Grizzly G0689 owner manual Thickness Stop Calibration, To adjust the thickness stop

Page 33

4.Loosen the lock nuts, then turn each adjust- ment bolt so that it just touches the cam when the lock lever is approximately halfway through its travel, then tighten the lock nuts.

Note: It is important that all four adjustment bolts are set equally. Failure to do this could cause the cutterhead to move during use, resulting in inconsistent planing.

Thickness Stop

Calibration

The thickness stop is set at the factory and should not require adjustment. However, with extended use, it is possible that the thickness stop may come out of adjustment. If you notice that use of the thickness stop is not producing results to your standards, you may need to adjust it.

Tools Needed

Qty

Hex Wrench 4mm

1

Hex Wrench 5mm

1

Wrench 8mm

1

To adjust the thickness stop:

 

1.Using a caliper to accurately measure the thickness, plane a board to exactly 1 1⁄4".

2.DISCONNECT PLANER FROM POWER!

3.Remove the side and top covers by perform- ing Steps 2–3from Drive Belt, starting on Page 28. Replace the elevation crank and raise the cutterhead approximately 1".

G0689 13" Planer

4.Locate the thickness stop bolt and lock nut. Manually rotate the thickness stop to the position shown in Figure 42.



AdX`Cji

IdjX]^c\

Hide7dai

 

I]^X`cZhh

8jiiZg]ZVY@c^[Z



Hide

IdjX]^c\

 

 

&I]^X`Ldg`e^ZXZ

Figure 42. Thickness stop adjustment.

5.Place the 1 1⁄4" thick board on the table and lower the cutterhead until the knife just touches the board when the knife is at its low- est position (turn the belt pulley to rotate the cutterhead as needed).

6.Loosen the lock nut and adjust the stop bolt as needed until it just touches the thickness stop, then re-tighten the lock nut.

7.Reassemble the machine, then check to see if the thickness stop is producing the desired results. Repeat as necessary.

-31-

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Model G0689 Planer with BUILT-IN Dust Collection Ss ,EAD from Leadbased PAINTS Table of Contents Introduction Manual Accuracy Functional OverviewContact Info Identification G0689 13 Planer Machine Data SheetModel G0689  !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29  !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4 53%3 2%#/--%.$%$- !##%33/2%3  53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2  !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#Unplugging during adjustments Additional Safety Instructions for Planers110V Operation Circuit RequirementsSetup Safety SetupInventory UnpackingPlacement Location Clean UpSite Considerations Workbench LoadAssembly Test Run To attach the elevation crank assemblyTo test run the machine Mounting Example of a direct mount setup G0689 13 PlanerOperations Operation Safety Basic ControlsReset Button ON/OFF SwitchElevation Crank Depth-of-CutThickness Stop Elevation LockCutterhead Elevation Scale To use the thickness stopPlaning Tips Basic OperationsTo use the planer StepWood Characteristics Type Wood TypesT20803-13 Replacement Knives AccessoriesT20448T20452 T20501 T20456 H0736 G7313-700 lb Capacity Shop FOX StandG8984-Single Roller Stand G8983-Tilting Roller StandG8985-5 Roller Stand G8983 G8985 G8984Cleaning MaintenanceSchedule LubricationTroubleshooting ServiceKnife Replacement Tools Needed QtyTo remove the knives To inspect the cutterhead, gib, and knives Motor To install the knivesTo replace the belt Drive BeltImpeller Belt To clean the feed rollersFeed Rollers Perform Steps 2-3 from Drive Belt onIf adjustment is necessary, proceed as fol- lows Elevation Lock AdjustmentTo adjust the elevation lock Extension Wing/ Table AlignmentThickness Stop Calibration To adjust the thickness stopSwitch wiring G0689 13 Planer Wiring DiagramMain Parts Breakdown PartsDescription Main Parts ListGear Large 70T Base Parts Breakdown Base Parts List 302 301 303 304 307 305 306 308 309 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7!  Warranty and Returns #ALL 4ODAYD&ORO! &2%%
Top Page Image Contents