Grizzly G0689 owner manual Impeller Belt, Feed Rollers, Perform Steps 2-3 from Drive Belt on

Page 31

Impeller Belt

The dust collection system on the Model G0689 is powered by a belt-driven impeller. The belt is very durable, but with extended use it may begin to slip, resulting in a reduction in dust collection performance.

Tools Needed

Qty

Hex Wrench 4mm

1

Hex Wrench 5mm

1

To replace the belt:

 

1.DISCONNECT PLANER FROM POWER!

2.Perform Steps 2–3 from Drive Belt on Page 28.

3.Remove the impeller belt by first rolling it off the cutterhead pulley, then remove it com- pletely (Figure 38).

Impeller Belt

Figure 38. Impeller belt.

4.Replace the belt with a new one, then re-assemble the removed components in the reverse order from which they were removed.

G0689 13" Planer

Feed Rollers

The feed rollers rotate in bushing blocks that are spring loaded. The feed rollers ride up on the board so that the roller pressure is maintained. If chips or sawdust build up between the bracket and bushing block, the amount of roller vertical travel will be reduced, potentially causing improp- er feeding of lumber through the machine (Figure

39).

BracketBushing

Block

Remove trapped sawdust from between

the bushing block and the bracket.

Figure 39. Location of potential trapped sawdust.

Periodically check and clean chips and sawdust from between the bushing blocks and brackets.

To clean the feed rollers:

1.DISCONNECT PLANER FROM POWER!

2.Remove the elevation crank and the top and side covers. This provides easy access to depress the rollers so that chips and sawdust can be easily removed.

3.Place a 4'' high block of wood between one of the feed rollers and the planer bed. Ensure that the block of wood is not under the cutterhead.

4.Lower the cutterhead assembly down just enough so that the roller is pushed up against the spring and pressure is off of the two brackets.

5.Remove any trapped material from between the roller assembly and bracket.

-29-

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Model G0689 Planer with BUILT-IN Dust Collection Ss ,EAD from Leadbased PAINTS Table of Contents Manual Accuracy Functional Overview IntroductionContact Info Identification G0689 13 Planer Machine Data SheetModel G0689  !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29  !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4 !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#  53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2 53%3 2%#/--%.$%$- !##%33/2%3  -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2Unplugging during adjustments Additional Safety Instructions for Planers110V Operation Circuit RequirementsUnpacking SetupSetup Safety InventoryWorkbench Load Clean UpPlacement Location Site ConsiderationsTo attach the elevation crank assembly Assembly Test RunTo test run the machine Mounting Example of a direct mount setup G0689 13 PlanerOperations Operation Safety Basic ControlsReset Button ON/OFF SwitchElevation Crank Depth-of-CutTo use the thickness stop Elevation LockThickness Stop Cutterhead Elevation ScaleStep Basic OperationsPlaning Tips To use the planerWood Characteristics Type Wood TypesG7313-700 lb Capacity Shop FOX Stand AccessoriesT20803-13 Replacement Knives T20448T20452 T20501 T20456 H0736G8983 G8985 G8984 G8983-Tilting Roller StandG8984-Single Roller Stand G8985-5 Roller StandLubrication MaintenanceCleaning ScheduleTroubleshooting ServiceTools Needed Qty Knife ReplacementTo remove the knives To inspect the cutterhead, gib, and knives Motor To install the knivesTo replace the belt Drive BeltPerform Steps 2-3 from Drive Belt on To clean the feed rollersImpeller Belt Feed RollersExtension Wing/ Table Alignment Elevation Lock AdjustmentIf adjustment is necessary, proceed as fol- lows To adjust the elevation lockThickness Stop Calibration To adjust the thickness stopSwitch wiring G0689 13 Planer Wiring DiagramMain Parts Breakdown PartsDescription Main Parts ListGear Large 70T Base Parts Breakdown Base Parts List 302 301 303 304 307 305 306 308 309 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7!  Warranty and Returns #ALL 4ODAYD&ORO! &2%%
Top Page Image Contents