Grizzly G0689 owner manual 302 301 303 304 307 305 306 308 309

Page 40

Warning Labels Breakdown and List

302

301

303

304

307

305

306

308

 

309

REF

PART #

DESCRIPTION

 

 

 

301

PLABEL-15B

HEARING PROTECTION LABEL VS

302

P0689302

MACHINE ID LABEL

303

PLABEL-57A

GLASSES/RESPIRATOR LABEL VS

304

P0689304

MODEL NUMBER LABEL

305

PLABEL-14A

ELECTRICITY LABEL 0.7"

REF

PART #

DESCRIPTION

 

 

 

306

PLABEL-12C

READ MANUAL LABEL VS

307

P0689307

GRIZZLY LOGO LABEL

308

PLABEL-62C

DISCONNECT POWER LABEL HS

309

P0689309

REMOVE COVER LABEL

Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels.

-38-

G0689 13" Planer

Image 40
Contents Model G0689 Planer with BUILT-IN Dust Collection Ss ,EAD from Leadbased PAINTS Table of Contents Manual Accuracy Functional Overview IntroductionContact Info Identification Machine Data Sheet G0689 13 PlanerModel G0689  !,7!93 53% !.3 !002/6%$$ 3!&%49 ,!33%33 7%. /0%2!4  !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%29 53%3!!2/5.$%$ %84%.3/..#/2$ 2!4%$4&/2/4%-!#.%!-0%2!%2  53%3 2%#/--%.$%$- !##%33/2%3 -!.9 -!#.%3 #!. %*%#4 7/2+0%#%3 4/7!2$ /0%2!4/2  !,7!93 ,/#+ -/,% !3%3 & 53%$ % %&/2% /0%2!4. -!#.%29#Additional Safety Instructions for Planers Unplugging during adjustmentsCircuit Requirements 110V OperationSetup Setup SafetyInventory UnpackingClean Up Placement LocationSite Considerations Workbench LoadTo attach the elevation crank assembly Assembly Test RunTo test run the machine Example of a direct mount setup G0689 13 Planer MountingOperation Safety Basic Controls OperationsON/OFF Switch Reset ButtonDepth-of-Cut Elevation CrankElevation Lock Thickness StopCutterhead Elevation Scale To use the thickness stopBasic Operations Planing TipsTo use the planer StepWood Characteristics Wood Types TypeAccessories T20803-13 Replacement KnivesT20448T20452 T20501 T20456 H0736 G7313-700 lb Capacity Shop FOX StandG8983-Tilting Roller Stand G8984-Single Roller StandG8985-5 Roller Stand G8983 G8985 G8984Maintenance CleaningSchedule LubricationService TroubleshootingTools Needed Qty Knife ReplacementTo remove the knives To inspect the cutterhead, gib, and knives To install the knives MotorDrive Belt To replace the beltTo clean the feed rollers Impeller BeltFeed Rollers Perform Steps 2-3 from Drive Belt onElevation Lock Adjustment If adjustment is necessary, proceed as fol- lowsTo adjust the elevation lock Extension Wing/ Table AlignmentTo adjust the thickness stop Thickness Stop CalibrationWiring Diagram Switch wiring G0689 13 PlanerParts Main Parts BreakdownMain Parts List DescriptionGear Large 70T Base Parts Breakdown Base Parts List 302 301 303 304 307 305 306 308 309 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7!  Warranty and Returns #ALL 4ODAYD&ORO! &2%%